For the formation of N+ doping, the antimony ions are mainly used for the fabrication of a BJT (bipolar junction transistor), CMOS (complementary metal oxide semiconductor), FET (field effect transistor) and BiCMOS (bipolar and complementary metal oxide semiconductor) process integration. Antimony is a heavy element and has relatively a low diffusion coefficient in silicon. Therefore, antimony is preferred as a candidate of ultra shallow junction for n type doping instead of arsenic implantation. Three-dimensional (3D) profiles of antimony are also compared one another from different tilt angles and incident energies under same dimensional conditions. The diffusion effect of antimony showed ORD (oxygen retarded diffusion) after thermal oxidation process. The interfacial effect of a SiO2/Si is influenced antimony diffusion and showed segregation effects during the oxidation process. The surface sputtering effect of antimony must be considered due to its heavy mass in the case of low energy and high dose conditions. The range of antimony implanted in amorphous and crystalline silicon are compared each other and its data and profiles also showed and explained after thermal annealing under inert N2gas and dry oxidation.

In this paper, in order to develop excellent Pb-free composition ceramics for ultrasonic sensor. The SnO2-doped (Na0.525K0.443Li0.037)(Nb0.883Sb0.08Ta0.037)O3)(abbreviated as NKL-NST) ceramics have been synthesized using the ordinary solid state reaction method. The effect of SnO2-doping on their dielectric and piezoelectric properties was investigated. The ceramics doped with 0 wt% SnO2 have the optimum values of piezoelectric constant(d33), piezoelectric figure of merit(d33·g33), planar piezoelectric coupling coefficient(kp) and density : d33= 195[pC/N], d33·g33=5.62 pm2/N.kp= 0.40, density= 4.436[g/cm3]. suitable for duplex ultrasonic sensor application.

We investigated the characterizations of carbon films fabricated by dual magnetron sputtering under various RF powers for the improvement of physical properties in carbon fiber (CF). All sputtered carbon films exhibited amorphous structure, regardless of RF powers, resulting in uniform and smooth surfaces. The hardness and elastic modulus are increased with the increase of RF power, and the adhesion and friction properties of carbon films were improved with the increase of RF power. In the results, The increase of RF power in the sputtering method improved tribological properties of the carbon films, and these attributes can be expected to improve the physical properties of the carbon fiber reinforcement plastics.

In this study, we fabricated the dual gate (DG) ion-sensitive field-effect-transistor (ISFET) with flexible polyimide (PI) extended gate (EG). The DG ISFETs significantly enhanced the sensitivity of pH in electrolytes from 60 mV/pH to 1152.17 mV/pH and effectively improved the drift and hysteresis phenomenon. This is attributed to the capacitive coupling effect between top gate and bottom gate insulators of the channel in silicon-on-transistor(SOI) metal-oxide-semiconductor (MOS) FETs. Accordingly, it is expected that the PI-EG based DG-ISFETs is promising technology for high-performance flexible biosensor applications.

We studied white organic light-emitting diodes using blue fluorescent and red phosphorescent materials.White single OLEDs were fabricated using SH-1 : BD-2 (3 vol.%) and CBP : Ir(mphmq)2(acac) (2 vol.%) as emitting layer (EML). The white single OLED using SH-1 : BD-2 (3 vol.% 8 nm) / CBP : Ir(mphmq)2(acac) (2vol.% 22 nm) as emitting layer showed maximum current efficiency of 8.8 cd/A, Commission Internationale del``Eclairage (CIE) coordinates of (0.403, 0.351) at 1,000 cd/㎡, and variation of CIE coordinates with (0.402 ±0.012, 0.35 ± 0.002) from 500 to 3,000 cd/㎡. The white tandem OLED using SH-1 : BD-2 (3 vol.% 12 nm) /CBP : Ir(mphmq)2(acac) (2 vol.% 18 nm) showed maximum efficiency of 19.6 cd/A, CIE coordinates of (0.354,0.365) at 1,000 cd/㎡, and variation of CIE coordinates with (0.356 ± 0.016, 0.364 ± 0.002) from 500 to 3,000 cd/㎡. Maximum current efficiency of the white tandem OLED was more twice as high as the single OLED. Our findings suggest that tandem OLED was possible to produce improved efficiency and excellent color stability.

In this paper, high quality AlN layers were regrown on AlN nanopillar structure with SiO2-dots by HVPE. Surface morphology of AlN layer regrown exhibited flatter than a conventional AlN template. The laterally overgrown AlN regions would consist of a continuous well coalesced layer with lower dislocation density than in the template because of the dislocation blocking and dislocation bending effects. Moreover, result of Raman spectroscopy suggest that the AlN nanopillar structure with SiO2-dots relieves the strain in the AlN layer regrown by HVPE.

The photoinduced hydrophilicity of TiO2/WO3 double layer films was fabricated by using a conventional rf-magnetron sputtering method. The photoinduced hydrophilic reaction of the TiO2 surface was enhanced by the presence of WO3 under the TiO2 layer by irradiation of a 10 W cylindrical fluorescent light bulb. However, when the TiO2 and WO3 layers were separated by an insulating layer, the surface did not appeared high hydrophilic,under the same light bulb. The enhanced photoinduced hydrophilic reaction can be explained by the charge transfer between TiO2 and WO3 layers. It was also demonstrated that visible light passing through the TiO2 layer could excite WO3. Thus, visible light can be used for the hydrophilic reaction in the present TiO2/WO3 system.

In this study, the properties of C-V degradation for thermal conductivity silicone rubber sample which is attached by copper-copper, copper-aluminum, aluminum-aluminum on upper-side and under-side has been measured at temperature of 80℃∼140℃. The results of this study are as follows. In case the frequency is increased, it found that the electrostatic capacity increased with increasing temperature to 80℃, 110℃, 140℃ regardless of kind of electrode. It found that the electrostatic capacity increased with becoming high temperature range of frequency regardless of kind of electrode. This result is considered to be caused by thermal absorption on the thermal conductivity silicone rubber sample. It found that the electrostatic capacity decreased with increasing temperature and frequency. This result is considered to be caused by molecular motion of C-F radical or OH radical.

In this paper, we fabricated organic compounds detector using the MWCNT/PMMA (multi-walled carbon nanotube / polymethylmethacrylate) composite film. We used polymer film as a matrix material for the device framework, and introduced CNTs for reacting with the organic compounds resulting in changing electrical conductivity. Spray coating method was used to form the MWCNT/PMMA composite film detector, and pattern formation of the detector was done by shadow mask during the spray coating process. We investigated changes of electrical conductivity of the detector before and after the organic compounds exposure. Electrical conductivity of the detector tended to decrease after the exposure with various organic compounds such as acetone, tetrahydrofuran(THF), toluene, and dimethylformamide (DMF). Finally we conclude that organic compounds detection by the MWCNT/PMMA composite film detector was possible, and expect the feasibility of commercial MWCNT/PMMA composite film detector for various organic compounds.

Rhodamine B (RhB) was utilized as a dye sensitizer for dye-sensitized solar cells (DSSCs) and its photovoltaic property was examined under the illumination of AM 1.5 G, 100 mWcm-2. DSSCs based on RhBexhibited typical photovoltaic properties with an open-circuit voltage (VOC) of 0.34 V, a short-circuit current (JSC) of 1.55 mA·cm-2, a fill factor (FF) of 50%, and a conversion efficiency (PCE) of 0.26%. In order to further improve the photovoltaic properties of RhB-based DSSCs, the effect of (i) incorporating a strong electron-donating NCS unit into the RhB molecular backbone, (ii) combining a bis-negatively charged zinc complex anion (Zn-dmit2, dmit=di-mercapto-dithiol-thione) with the amine cation of RhB, (iii) co-adsorbing RhB dyes with chenodeoxycholic acid (CDCA) molecules onto porous TiO2 electrodes, was investigated and discussed.

This paper is designed to find out where power reaches the highest point as the load of solar cells varies. In addition, the current and power were measured when irradiation changes, and the correlation between current and power was investigated. On top of that, experiments were conducted with the light volume kept constant and with the incoming light angle changing in order to figure out the incoming light angle that produces the most power and to conduct analyses. It was ascertained that if the load increases, the current decreases and the voltage increases. Since the power of 0.9828[W] was the highest when measurements were done, it can be said that when a load of 30[%] is applied to the solar cells, they are the most efficient.

In this paper, the power generation efficiency of the 4 [kW] fixed-concentrated type photovoltaic power generation system and that of the 4 [kW] single axis trace type photovoltaic power generation system were compared. For that purpose, the two types of photovoltaic power generation systems have been in operation for 1year on an experimental basis. The amounts of power generated by the two types during the months of January through December and the characteristics of their operating times during the same period have been compared and analyzed. For the study, the type with higher efficiency was selected and the following conclusions have been reached. It was shown that the amount of power generated and the average operation times during the spring months of March through May are higher that those of the summer months of June through August when more sunlight is available. The reason for this phenomenon is thought to be that as the temperatures of the solar panel surface and the surrounding environment go up, the electric current decreases.

Sound Masking System technology as by sound the same on all bands and artificially generates a constant sound shield People want to hear or recognize the people with the noise generated from the interior of the way. Prevent hearing or prevent recognition by using the technology to control the audible frequency band Continue to emit constant and uniform shielding sound audible frequency band Even the security content of speech (20 Hz ~20 KHz). That interception laser eavesdropping, internal solicitations, during recording Or delay the decoding was a result of the effect of interference calculated Experience noise disturbance index is applied around the Stress Index is the average index is 10.16 was a luxury for the average index is then applied to the index 3.07 Noise is significantly lower stress level has improved noise conditions.