Flexible micro-supercapacitors (MSCs) based on 2D MXenes offer strong potential for next-generation energy storage in wearable and integrated electronics, yet still face critical challenges such as limited energy density, mechanical reliability, and scalable large-area manufacturing. This review surveys recent strategies to address these limitations, with a particular focus on fabrication techniques and wafer-level integration approaches. Wafer-scale processing on both rigid and flexible substrates has emerged as a key milestone toward scalable, high-yield industrial production of flexible MSCs. By examining the strengths and drawbacks of current fabrication strategies, this review highlights essential directions for advancing MXene-based flexible MSCs toward practical and widespread application.
Metal halide perovskite materials have emerged as promising candidates for next-generation optoelectronic applications owing to their outstanding optical properties and tunable emission characteristics. However, their practical application is hindered by poor environmental stability, especially under conditions of heat, moisture, and UV exposure, necessitating effective encapsulation strategies. This review summarizes recent progress in enhancing the environmental stability of perovskite nanocrystals through polymer matrix embedding, inorganic oxide encapsulation, and compositionally matched core-shell structures using homogenous perovskite derivatives. We discuss how polymers enhance the environmental and moisture stability of perovskite nanocrystals, how oxide-based shells (e.g., SiO₂, TiO₂) contribute to thermal robustness and barrier protection, and how homostructural core-shells provide lattice-matched defect passivation with improved long-term durability. A comprehensive understanding of the advantages and limitations of each encapsulation strategy, along with their rational integration, can accelerate the commercialization of perovskite-based technologies in various applications such as highcolor- purity displays, color conversion filters, and flexible optoelectronic devices.
Porous polymeric structures with piezoelectric properties have attracted considerable attention in the fields of biomaterials and tissue engineering due to their ability to convert mechanical stimuli into electrical signals. However, conventional fabrication methods for porous structures often face limitations in controlling pore architecture, maintaining structural uniformity, and achieving process reproducibility, in addition to requiring complex processing conditions. To address these issues, we propose a facile and reproducible fabrication method for porous poly (vinylidene fluoride) (PVDF) piezoelectric sponges using molded sugar cubes as sacrificial pore templates. By adjusting the particle size of the sugar templates, the pore size and distribution of the sponges could be effectively controlled, and a uniform open-pore network was achieved. The fabricated sponges were evaluated with a focus on pore morphology, mechanical behavior, and piezoelectric performance depending on the sugar particle size, and these evaluations confirmed the structural properties and functional efficacy. This study presents a simple and reproducible fabrication strategy along with a quantitative analysis method for porous structures, which is expected to enhance process accessibility and practical applicability in the development of piezoelectric polymer-based biomaterial platforms.
This study developed a dielectric composition for high-capacitance MLCCs with C0G and U2J temperature compensation characteristics (Class I) under reducing conditions. The potential application of this composition in highpermittivity class I MLCCs was examined. Using (Ba₀.₂₄Ca₀.₁₆Sr₀.₆)(TiₓZr₁₋ₓ)O₃. XRD analysis showed that secondary phases like Sr₂TiO₄ and TiO₂ formed at higher Ti content, affecting the stoichiometric balance. Adjusting the Ti/Zr molar ratio resulted in a dielectric constant of 41.2 ~ 105, a dielectric loss of 0.082 ~ 0.174%, and insulation resistance above 1.6 × 1013 ohms at 25℃. The TCC shifted from C0G to U2J as the Ti/Zr ratio increased, but the composition enabled the design of high-capacitance and high-voltage MLCCs with favorable dielectric and electrical properties.
The thermal management issue in OLED (organic light emitting diode) devices has a significant impact on the efficiency, reliability, and life time of the device. In particular, in OLED systems with multipolar or double cathode electrodes, it is important to accurately interpret the effect of heat generated by current flow between electrodes on the emitting layer. In this study, the governing equation was established based on the heat conduction equation to mathematically model and analyze this heat distribution, and the heat distribution analysis was performed using the COMSOL program. It was confirmed that the temperature generated in the OLED with the double cathode structure reached a maximum of 343.157 K centered on the emitting layer. The heat distribution generated in the proposed OLED structure with the double cathode electrodes was confirmed to be highly distributed in the center toward the double cathode electrodes, which is believed to be because the arrangement of the double cathode electrodes improves the symmetrical distribution of temperature while reducing power consumption.
Lithium-ion batteries are utilized as an energy source for electric vehicles because of their advantages such as excellent cyclability, high energy density, high capacity, high efficiency, and low price. However, lithium-ion batteries use combustible electrolytes, which have also reported problems related to fire safety. Therefore, research on the fire safety of lithium-ion batteries is actively being conducted. In this study, detection criteria for the fire safety of lithium-ion batteries were proposed through incremental capacity analysis (ICA) and frequency analysis. The experimental results showed that the battery micro internal short circuit (MISC) indicator could be identified through changes in specific frequency bands and fluctuations in the ICA curve.
Drain Induced Barrier Lowering (DIBL) was analyzed when the channel of Gate-All-Around (GAA) FET, which is the most promising in the miniaturizing transistor structure, has an elliptic cross-section. The oxide film structure used a stacked Metal-Ferroelectric-Metal-Insulator-Semiconductor (MFMIS) structure using SiO2 and ferroelectric. An analytical DIBL model was presented to analyze the DIBL in elliptic GAA FET with ferroelectric. Its validity was proven by comparing the results of other papers. As a result, the Drain Induced Barrier Rising (DIBR) effect, that is, the negative DIBL effect, appeared depending on the ferroelectric thickness tfe, and the ratio of the remanent polarization Pr and coercive field Ec in the ferroelectric, Pr/Ec. The DIBL varied linearly with tfeEc/Pr, and the slope depended on the rate of change for the drain voltage of the ferroelectric charge Q, dQ/dVds. The tfeEc/Pr value satisfying DIBL=0 mV/V decreased as eccentricity increased. The ferroelectric thickness tfe will have to be decreased because the subthreshold swing increases if the Pr/Ec is increased to reduce the tfeEc/Pr value. The threshold voltage increased at this time, but the effect was minimal.
The increasing demand for renewable energy is driving the rapid expansion of the offshore wind industry, leading to intensified research on subsea cables. These cables endure combined thermal, electrical, and mechanical stresses, with mechanical stress being a critical failure factor. Environmental changes, such as seabed scouring, free spans, and seismic activity, accelerate cable degradation by introducing additional dynamic loads. Conventional monitoring systems primarily track thermal stress, lacking the ability to assess mechanical impacts. This study develops a system to simultaneously measure thermal and mechanical stress in subsea cables. Laboratory experiments confirm the system’s reliability, showing a temperature measurement error within 0.8% at 60℃ and a strain measurement error within 13% at 378 με. The proposed system aims to enhance failure prediction and maintenance strategies for offshore wind subsea cables.
This study investigates the insulation performance of a 66 kV dry-type submarine cable used in offshore wind farms under mechanical aging. During installation and operation, submarine cables are subjected to various mechanical stresses, including tension, compression, and bending, which can lead to insulation deterioration. In this study, XLPE samples extracted from a submarine cable were prepared and subjected to controlled tensile strain below the yield strain to evaluate their mechanical and electrical performance. Changes in tensile strength, elongation, and tan δ (dielectric loss factor) were measured to assess the extent of aging. The results indicate that as the applied strain and exposure duration increased, tensile strength and elongation decreased, while tan δ values increased, signifying a decline in electrical insulation performance. A strong negative correlation (R = -0.809) was observed between tan δ and tensile strength, demonstrating that mechanical aging significantly affects electrical properties. These findings highlight the importance of minimizing excessive mechanical stress during the installation and operation of submarine cables. The results provide valuable insights for enhancing the reliability of submarine cables in offshore wind farms and emphasize the necessity of optimized design and maintenance strategies to mitigate the effects of mechanical aging.
In this study, we investigated the electrical stability and performance enhancement of In₂O₃ thin-film transistors (TFTs) through hydrogen peroxide (H₂O₂) and ultraviolet (UV) treatment under controlled temperature conditions. The In₂O₃ TFTs were fabricated using a sol-gel process, followed by H₂O₂ treatment at 40, 50, and 60℃ in combination with UV irradiation. The impact of these processing conditions on the device characteristics, including mobility (μ), threshold voltage (Vth), subthreshold swing (S/S), and on/off current ratio, was systematically analyzed. The results indicate that the 50℃ TFTs exhibited the most stable electrical performance, with minimal Vth shift under negative bias stress (NBS) conditions and optimized switching behavior. Furthermore, static inverter measurements confirmed the reliable voltage transfer characteristics (VTCs) and gain performance of the optimized In₂O₃ TFTs. These findings suggest that the proposed H₂O₂ and UV treatment technique can effectively improve the reliability and long-term stability of In₂O₃-based electronic devices, making them promising candidates for future electronic applications.
With the expansion of offshore wind farms, research on power cables for delivering electricity from offshore to onshore has become increasingly important. In offshore wind farms, submarine cables are introduced and secured to the platform through J-tube conduits. During this process, the cables are exposed to three distinct thermal profiles: high temperatures in the upper section, temperature fluctuations due to water level changes in the middle section, and low temperatures in the seabed region. This study investigates the impact of thermal variations on the insulation performance of submarine cables. To analyze this effect, accelerated aging tests were conducted on both insulation specimens and actual cables. Additionally, dielectric breakdown tests were performed to quantitatively assess insulation degradation. Experimental results revealed that the insulation performance of the specimens exposed to periodic temperature fluctuations due to water level changes deteriorated by up to 7.5%. Based on these findings, the vulnerable sections of submarine cables in offshore wind farms were identified. Furthermore, this study emphasizes the necessity for monitoring and protective measures to mitigate insulation degradation in these critical regions.
The composite specimens of (1-x)(La0.7Sr0.3)MnO₃-xBaTiO₃ (x = 0.05 ~ 0.3) were synthesized using the conventional solid-state reaction method, and the sintering temperature and time were 1,300℃ and 3 hours, respectively. As a result of observing the structural characteristics, the crystal structure of LSMO-BT solid solution was shown in which the rhombohedral LSMO phase and the tetragonal BT phase were separated and distributed, respectively. And fine grains having relatively small and uniformly distributed grains with sizes ranging from approximately 0.4 to 0.5 μm and pores within the specimens were observed. Notably, variations in the BT content did not significantly affect the grain size or porosity distribution, and a relative density of about 90% or more was shown. The resistivity, temperature coefficient of resistance (TCR), and B25/65-value of the 0.7LSMO-0.3BT specimen at room temperature showed the highest values of 1.94 Ω-cm, 0.292 %/℃, and 464 K, respectively. The resistivity behavior of the LSMO-BT composites matched well with the small polaron hopping conduction model.
Conductive inks are essential for developing flexible and wearable electronic devices, where printability and electrical performance must be finely balanced. However, achieving high conductivity while minimizing costly silver filler content remains a key challenge in ink formulation. In this work, we demonstrate that a simple ball-milling process transforms spherical silver particles into platelet-shaped fillers, dramatically enhancing conductivity at equivalent filler loading. The resulting inks show a reduction in sheet resistance from ~180 Ω/□ to ~ 0.57 Ω/□ at 70 wt% filler content, with improved performance attributed to surface-to-surface contact between platelets. Moreover, we show that filler content influences not only electrical conductivity but also ink viscosity, with the 53.8 wt% formulation achieving a practical balance between conductivity, processability, and cost. This morphology- and composition-controlled ink design offers a scalable strategy for manufacturing high-performance, cost-effective conductive inks suitable for next-generation printed electronics.
The continuous and long-lasting monitoring of physiological signals induced from the human body is crucial for health monitoring, disease diagnosis, and treatment. In this study, we have reported the Seebeck effect-based flexible selfpowered temperature sensor which can convert the electric signals from lateral temperature difference. For demonstrating temperature sensor arrays, the p-type thermoelectric (TE) composite films were fabricated by dispersing the Bi0.5Sb1.5Te3 (BST) powders inside poly-vinylidene fluoride matrix and subsequently attached to the patterned electrode foils. The inorganic BST powders-embedded TE composite films with activated area of 0.5 × 1 cm² harvest a maximum voltage of 1.7 mV, a maximum current of 5.6 mA, and an output power of 2.6 nW from the temperature gradient (ΔT) of 20 K. Finally, the fabricated selfpowered temperature sensor array well detected the pattern images of external thermal source of ΔT = 20 K. This study manifests flexible temperature sensor array which paves the way for further advancements in this field.
NTC thermistors are essential components widely used for temperature sensing in various electronic sensor applications. However, conventional NTC thermistor ceramics typically require high sintering temperatures above 1150℃, necessitating the use of high-cost noble metal electrodes such as palladium (Pd) or platinum (Pt), which increases the overall manufacturing cost. In this study, low-melting-point oxides were successfully introduced as sintering aids to reduce the sintering temperature of NiMnCoO₄-based semiconducting ceramics. As the additive content increased, the B constant and average grain size exhibited an increasing trend, while the sample containing 5 wt% additives showed the lowest room-temperature resistivity. Furthermore, samples sintered at 1000℃ demonstrated slightly higher room-temperature resistivity and B constant values compared to those sintered at 1150℃. These results confirm that the addition of low-melting-point oxides is effective in lowering the sintering temperature of NiMnCoO₄ ceramics, suggesting the potential for reducing production costs and improving design flexibility in thermistor fabrication.
First
Prev
