This study aimed to elucidate factors limiting power conversion efficiency (PCE) in GaN-based micro-light-emitting diodes (μ-LEDs). To this end, we investigated the effects of operating temperature and chip-size of μ-LEDs on their efficiency. For the investigation, 460 nm-emitting μ-LEDs with various chip-sizes were fabricated; then their characteristics were carefully measured from 100 to 400 K. As the chip-size decreases and the operating temperature increases, their PCE and external quantum efficiency (EQE) decrease, while voltage efficiency (VE) increases. This indicates that the EQE plays a more important role than the VE in determining the PCE of μ-LEDs. Particularly, for a chip-size of 20 × 20 μm², the EQE was very lower and the ideality factor was unexpectedly higher compared to the others for all operating temperatures, which is believed to be due to the critical plasma damage at the sidewall during dry-etching process for the chip-size < 20 × 20 μm².

One method to increase the output of solar modules is the application of the Half-cut technique, which requires a scribing process involving direct irradiation of infrared lasers on the solar cells. During this process, the laser melts the surface of the solar cells at high temperatures, enabling mechanical division, but this can lead to output loss due to thermal degradation caused by the laser. To minimize such losses, a low-temperature and low-loss division method has been devised. In this study, we compared the electrical characteristics and leakage currents affecting output degradation between the newly devised low temperature and low-loss cell division method and the conventional laser division method. Additionally, we conducted a 3-point flexural test to evaluate the mechanical properties of both methods.

The purpose of this paper is to help those who research and develop solar cells in university laboratories and industrial sites understand the most basic and important quantum efficiency measurement and analysis method in analyzing solar cell performance. Starting with the definition of quantum efficiency, we calculate the theoretical current density according to the band gap of the solar cell material from the solar spectrum, along with a detailed introduction to the measurement and analysis methods, and measure and analyze the theoretical current density and quantum efficiency. We discuss in depth how to analyze the performance of solar cells through Quantum efficiency measurement and analysis of solar cells is a very useful method that can give intuition to solar cell performance analysis as it can analyze solar cells according to depth (front emitter, bulk, rear surface). Students and researchers who study solar cells with a deep understanding of theoretical current density and quantum efficiency measurement analysis are expected to use it as a basis for analyzing solar cell performance.

Crystalline silicon solar cells have attracted great attention for their various advantages, such as the availability of raw materials, high-efficiency potential, and well-established processing sequence. Tunnel oxide passivated contact (TOPCon) solar cells are widely regarded as one of the most prospective candidates for the next generation of high-performance solar cells because an efficiency of 26% has been achieved in small-area solar cells. Compared to n-type TOPCon solar cells, the photo conversion efficiency (PCE) of p-type TOPCon is slightly higher. The highest PCEs of p-type TOPCon and n-type TOPCon solar cells are 26.0% and 25.8%, respectively. Despite the highest efficiency in small-area cells, limited progress has been achieved in p-type TOPCon solar cells for large are due to their lower carrier lifetime and inferior surface passivation with the boron-doped c-Si wafer. Nevertheless, it is of great importance to promoting the p-type TOPCon technology due to its lower price and well-established manufacturing procedures with slight modifications in the PERC solar cells production lines. The progress in different approaches to increase the efficiencies of p-type TOPCon solar cells has been reported in this review article and is expected to set valuable strategies to promote the passivation technology of p-type TOPCon, which could further increase the efficiency of TOPCon solar cells.

p-type Tunnel Oxide Passivating Contacts (TOPCon) solar cell is fabricated with a poly-Si/SiO_x structure. It simultaneously achieves surface passivation and enhances the carriers’ selective collection, which is a promising technology for conventional solar cells. The quality of passivation is depended on the quality of the tunnel oxide layer at the interface with the c-Si wafer, which is affected by the bond of SiO formed during the subsequent annealing process. The highest cell efficiency reported to date for the laboratory scale has increased to 26.1%, fabricated by the Institute for Solar Energy Research. The cells used a p-type float zone silicon with an interdigitated back contact (IBC) structure that fabricates poly-Si and SiO_x layer achieves the highest implied open-circuit voltage (iV_oc) is 750 mV, and the highest level of edge passivation is 40%. This review presents an overview of p-type TOPCon technologies, including the ultra-thin silicon oxide layer (SiO_x) and poly-silicon layer (poly-Si), as well as the advancement of the SiO_x and poly-Si layers. Subsequently, the limitations of improving efficiency are discussed in detail. Consequently, it is expected to provide a basis for the simplification of industrial mass production.

We investigated the properties of vanadium oxide (VOx) buffer layers deposited by a dual RF magnetron sputtering method under various target powers for inverted organic solar cells (IOSCs). Sputter fabricatged VOx thin films exhibited higher crystallinity with the increase of target power, resulting in a uniform and large grain size. The electrical properties of VOx films are improved with the increase of target power because of the increase of V content. In the results, the performance of IOSCs critically depended on the target power during the film growth because the crystalllinity of the VOx film affects the carrier mobility of the VOx film.

As energy depletion and environmental pollution problems are intensified, research has been conducted actively on alternative energy sources, an eco-friendly and continuous available energy conversion system. So has been organic solar cells whose efficiency is improved to 18.32%. The photoactive layer inside the solar cell is composed of a donor and a acceptor, and the combination of materials capable of effectively exchanging electrons greatly affects the efficiency of the organic solar cell. Accordingly, various researches have been conducted to improve the efficiency, and the maximum efficiency could be achieved by a solar cell with high carrier generation and low charge recombination characteristics through the introduction of a non-fullerene acceptor and material reconstruction. Organic solar cells are still difficult to commercialize due to their efficiency limitations and light stability, but if a photoactive layer consisting of a donor capable of efficiently absorbing long-wavelength light and an acceptor capable of forming an appropriate energy level is designed, the efficiency of the organic solar cell will reach 20%.

The high power of a shingled photovoltaic module can be attributed to its low cell-to-module loss. The production of high power modules in limited area requires high efficiency solar cells. Shingled photovoltaic modules can be made by divided solar cells, which can be produced by the laser scribing process. After dividing the 21% PERC cell using laser scribing, the efficiency decreased by approximately 0.35%. However, there was no change in the efficiency of the solar cell having relatively lower efficiency, because the laser scribing process induce higher heat damages in solar cells with high efficiency. To prove this phenomena, the J₀ (leakage current density) of each cell was analyzed. It was found that the J₀ of 21% PERC increased about 17 times between full and divided solar cell. However, the J₀ of 20.2% PERC increased only about 2.5 times between full and divided solar cell.

Raman spectra of a-C:H thin films deposited with an unbalanced magnetron sputtering system showed that the G peak shifted to a higher wavenumber as the target power density increased and ID/IG ratio increased from 0.902 to 1.012. Moreover, the transmittance of a-C:H films fabricated at 60 nm tended to decrease with increasing target power density; at 550 nm in the visible light region, the transmittance decreased from 69% to 58%. The rms surface roughness values of the a-C:H thin films decreased with increasing target power density, and varied from 1.11 nm to 0.71 nm. In order to achieve efficient light trapping, the light scattering at the rough interface must be enhanced. Consequently, the surface roughness of the thin film will decrease with the target power density. Further, the refractive index and reflectivity of the a-C:H thin films increased with increasing target power density; however, the Brewster angle decreased with the target power density. Hence, dye-sensitized solar cells using an a-C:H antireflective coating increased the CE, VOC, and JSC by approximately 8.6%, 5.5%, and 4.5%, respectively.

Micro-LEDs show lower efficiencies compared to general LEDs having large areas. Simulations were carried out using ray-tracing software to investigate the change in light extraction efficiency and light distribution according to chip-size of blue flip-chip micro-LEDs (FC μ-LEDs). After fixing the height of the square FC μ-LED chip at 158 μm, the length of one side was varied, with dimensions of 2, 5, 10, 30, 50, 100, 300, and 500 μm. The highest light-extraction efficiency was obtained at 10 μm, beyond which the efficiency decreased as the chip-size increased. The chip size-dependence of the FC μ-LEDs both without the patterned sapphire substrate, as well as vertical FC μ-LEDs, were analyzed.

Lead zirconate titanate/poly-vinylidene fluoride (PZT/PVDF) piezoelectric devices were fabricated by incorporating carbon nanotubes (CNTs), for use as flexible energy harvesting devices. CNTs were added to maximize the formation of the β phase of PVDF to enhance the piezoelectricity of the devices. The phase transition of PVDF induced by the addition of CNTs was confirmed by analyzing the X-ray diffraction patterns, scanning electron microscopy images, and atomic force microscopy images. The enhanced output efficiency of the PZT/PVDF piezoelectric devices was confirmed by measuring the output current and voltage of the fabricated devices. The maximum output current and voltage of the PZT/PVDF piezoelectric devices was 200 nA and 350 mV, respectively, upon incorporation of 0.06 wt% CNTs.

The amount of electric power for photovoltaic power generation depends on the location of the power plant and the direction of solar cell. The solar cell controls the generation of solar power plants. Therefore, the structure of solar cell, manufacturing method, and optic technology were factors contributing to increased solar cell efficiency; however, the technical limit has been reached. Herein, we propose a new method to increase the solar cell efficiency using a wavelength conversion technology that converts ultraviolet and infrared rays, which are not effectively used in solar cells, into effective wavelength of solar cell. We used fluoride Na(Ca)YF₄ phosphor for wavelength conversion. Then, a wavelength-conversion fluorescent paste, prepared using an organic-silicon binder, was used to prepare a film that was applied to Si solar cells. It was confirmed that conversion efficiency improved by 5% or more.

In this study, we design, model, and analyze a compound generator that combines the axial flux permanent magnet (AFPM,) and radial flux permanent magnet (RFPM), which is expected to increase power generation by allowing the magnets to be placed on the upper, lower, left, and right sides of the same-sized generator. Through the design, modelling, and analysis of AFPM and RFPM compound generators, the generator load evaluation results rated output of 500.25 W and efficiency of 87.60%, respectively, at a rated speed of 600 rpm. By employing this complex generation system,these findings are expected to contribute to the activation of a small power generation system.

We fabricated 1-D and 2-D diffraction gratings of SiOx anti-reflection (AR) film grown on a quartz substrate and integrated them into a c-Si photovoltaic (PV) submodule. The light-trapping effect of the resulting submodules was studied in terms of the oblique optical incident angle, θ_i. As the θ_i increased, solar conversion efficiency, η, was improved as expected by the increased optical transmission caused by the grating. For θ_i≤30°, the relative solar conversion efficiency, Δη, of a 1-D SiOx (t=300 nm) grating, compared to that of a flat SiOx AR-coated integrated PV submodule, was improved very little, with a small variation of within 2%, but increased markedly for θ_i≥40°. We observed a change of Δη as large as 10.7% and 9.5% for the SiOx grating of period t=800 nm and 1200 nm, respectively. For a 2-D SiOx (t=300 nm) grating integrated PV submodule, however, the optical trapping behavior was similar in terms of θ_i but its variation was small, within ±1.0%.

P3HT:PCBM bulk heterojunction solar cells added with ferroelectric polymer were fabricated and characterized. By incorporating P3HT:PCBM solar cell with P(VDF-TrFE) ferroelectric additive, the power conversion efficiency was increased up to nearly 50%. Photoacoustic analysis on this phenomena was carried out for the first time. Through this study, we find that the ferroelectricity of the polymer additive plays the key role in the enhancement of the power conversion efficiency of the organic solar cell by suppressing the non-radiative recombination of charge transfer exciton more effectively.

The characterizations of zinc oxide (ZnO) buffer layers grown by unbalanced magnetron (UBM) sputtering under various substrate temperatures for inverted organic solar cells (IOSCs) were investigated. UBM sputter grown ZnO films exhibited higher crystallinity with increasing the substrate temperature, resulting in uniform and large grain size. Also, the electrical properties of ZnO films are improved with increasing substrate temperature. In the results, the performance of IOSCs critically depended on the substrate temperature during the film growth because the crystalllinity of the ZnO film affect the carrier mobility of the ZnO film.

An improvement of light-extraction efficiency of organic light-emitting diodes was studied by using random-textured films (RTF). Device was made in a structure of RTF/glass/ITO/TPD/Alq3/LiF/Al. RTF mold was made by spreading PDMS solution on a sandpaper. By pressing this mold on the glass substrate pre-coated with ZPU material, the RTF was obtained. From this study, there was an improvement of external quantum efficiency by about 30% in the device with the random-textured film (RTF 40) compared to that of the reference one.

A new information society of late has arrived by the rapid development of various information & communications technologies. Accordingly, mobile devices which are light and thin, easy and convenient to carry on the market. Also, the requirements for the larger television sets such as fast response speed, low-cost electric power, wider visual angle display are sufficiently satisfied. The currently most widely studied display material, the Organic Light-emitting Diodes(OLEDs) overwhelms the Liquid Crystal Display(LCD), the main occupier of the market. This new material features a response speed of more than a thousand times faster, no need of backlight, a low driving voltage, and no limit of view angle. And the OLEDs has high luminance efficiency and excellent durability and environment resistance, quite different from the inorganic LED light source. The OLEDs with simple device structure and easy produce can be manufactured in various shapes such as a point light source, a linear light source, a surface light source. This will surely dominate the market for the next generation lighting and display device. The new display utilizes not the glass substrate but the plastic one, resulting in the thin and flexible substrate that can be curved and flattened out as needed. In this paper, OLEDs device was produced by changing thickness of Teflon-AF of hole injection material layer. And as for the electrical properties, the four layer device of ITO/TPD/Alq3/BCP/LiF/Al and the five layer device of ITO/Teflon AF/TPD/Alq3/BCP/Lif/Al were studied experimentally.

Photo electrode is an important component of DSSC, so this paper did some research on it. Through the method of adding PEG additive into TiO2 paste, the electrical characteristics and efficienciesof DSSCs with photo electrode surface area were studied. In the case of not adding PEG in TiO2 paste,26 ㎛ thickness TiO2 photo electrode shows 5.081% efficiency. The highest short circuit current densitywas 10.476 mA/cm2. The structure of porous TiO2 film can be controlled through changing the PEGadditive amount in TiO2 paste and the molecular weight of PEG. When the additive amount of PEG20,000 in TiO2 paste reaches 5%, the peak efficiency with 26 ㎛ thickness TiO2 photo electrode was5.387% and its highest current density were 11.084 mA/cm2.

Cs3Sb photocathode was formed by newly developed process and successive in-situ lightingdevices were fabricated in a process chamber. R, G, and B phosphors were applied on the anode plate,respectively. Major parameters such as brightness, power consumption, and efficacy were measured. Thewavelength of LED excitation source was 450 nm. Both high power and low power modes were appliedin the measurement. Measurement values were clearly differentiated by the voltage application modes. The measured values of each parameter was good enough to be applied for general lighting source. Theresults showed that Cs3Sb photocathode formed in atmospheric conditions was functioning as good as thephotocathode formed in UHV conditions, and thus it could be applied to advanced lighting devices.

Five factors are identified, which affect the performance of optical filter: 1) type of opticalglass, 2) existence of Fe, 3) photo pic coating type, 4) coating form, and 5) coating thickness. If weconsider all the levels of five factors, there are 360 possible candidates. We determined five evaluationcriteria, which can be used to evaluate possible candidates. For the performance measures we selectedwhite-state avearge voltage, black-state average voltage, and black-state error rate. And we addedeconomic criterion and quality and maintenance criterion. Through the two-step statistical analysis ofwhite-state avearge voltage, black-state average voltage, and black-state error rates, we selected finalfour candidates. Based on the five criteria we finally determined optimal optical filter using AHP.

Because of a waveguiding effect and total internal reflection caused by a difference inrefractive indices, only 20% of generated light is emitted to the air and the rest is trapped or absorbed inthe device. An improvement of outcoupled efficiency of organic light-emitting diodes was studied using amicrolens array. Mold of microlens array was fabricated by using photo-lithography with the AZ9260photoresist, and the microlens array was formed onto the glass substrate using the UV curing agentnamed ZPU13-440. Device structure consists of microlens/glass/ITO/TPD/Alq3/LiF/Al. It was found thatthere is an improvement of external quantum efficiency by about 20% at the same current density for thedevice with the microlens array compared to that of the reference one. Simulated outcoupled efficiencyshows the improvement by about 20% for the device with the microlens array compared to that of thereference one. These results are consistent with the experimental ones

Photo electrode is an important component for DSSC. DSSCs electrical characteristics and efficiencies fabricated with different TiO2 photo electrodes thickness and modified phoro electrode surface area were studied. 11 ㎛ TiO2 photo electrode shows a 4.956% efficiency. The highest short circuit current density was a 9.949 mA/cm2. Efficiencies and short circuit current density increased as tape casting thickness decreased. Modified surface area of the photo electrode by needle stamp processing were studied. 200 times needle stamp processing on photo electrodes shows a highest 5.168% efficiency. Also the short circuit current density was a 10.261 mA/cm2.

In this work, according to temperature and time of hydrothermal synthesis, the electrochemical properties of TiIO2 particle using TTIP based on thanging temperature and time in the hydrothermal synthesis were analyzed and optimized temperature and time were derived. When hydrothermal synthesis were analyzed and optimized temperature and time were derived. When hydrothermal synthesis temperature and time were 200℃ and 1 h, respectively. The fabricated DSSC delivered the best electrochemical properties. In that case, TiO2 particle size was 13.018 nm, electron transport time was 2.34×103s and recombination time was 4.01×102s. The lowest impedance of 13.52 Ω and Voc, Jsc, FF is 0.70 V, 11.50 mAcm2, 65.62%, respectively and corresponding efficiency of 5.34% was considered as the optimal.

In this paper, the characteristics of a carbon nanotube composite heat sink proposed to replace the advanced Al heat sinks for LED lighting devices were studied. Proposed CMP-PLA heat sink was made by mixing 20∼70 wt% carbon nanotube, 20∼70 wt% bio-degradable polymer of melt-blended PLA (poly lactic acid) and PBS (poly butylene succinate) and PLA nucleating agents composed of the mixture of soybean oil and biotites, at 150∼220℃ with 1,000∼1,500 rpm. Optical and electric characteristics of 7.5W LED lighting devices using heat sinks with such prepared CMP-PLA were investigated. And, the properties of the heat, which was not released from the CMP-PLA type heat sinks, was also investigated. The color temperature of LED lighting devices using the CMP-PLA heat sinks was 5,956 K,which is x= 0.32 and y= 0.34 in the XY chromaticity, and the color rendering index was 75. The luminous flux and the luminous efficiency of LED lighting devices using the CMP-PLA heat sinks was 540.6 lm and 72.68 lm/W respectively. Measured initial temperature of the heat sinks was 27℃, and their temperature increased as time to be saturated at 52℃ after an hour.

Performance of organic light-emitting diodes incorporating microlens array was simulated using a Light Tools software. Use of microlens array can help the light to escape out of the device. We simulated a reference device that is consisted of reflection layer, emissive layer, and flat transparent substrate. And in this reference device, outcoupled efficiency of 22% was obtained. Several shapes of microlens were applied such as hemisphere, trapezoid, cone, and rectangular parallelepiped. The results showed the improvement of outcoupled efficiency of the device with microlens compared to that of the reference one. And from the analyses of the simulated data, the obtained appropriate shape of microlens is hemisphere, and the improvement of the device with hemispherical lens is 57% higher than that of the reference one.

In this paper, the low-temperature sintering of TiO2 is approached to solve the problem of high temperature sintering which decreases the interconnection between particles or between substrate and particle. TiO2 paste is prepared with Titanium (Ⅳ) isopropoxide as the precursor material and calcinate at different conditions (low temperature). In the results, since the changing of temperature and time of sintering, crystalline phase do not change and the intensities of anatase, rutile phase are higher. At 110℃, 7 h sintering condition, crystalline size of anatase and rutile phase are the smallest which are 13.07 and 17.47 nm, respectively. In addition, the highest zeta potential is about 32.77 mV and the repulsive force increases thus leading to the best of the dispersion characteristics between TiO2 particles. Futhermore, DSSCs at that condition exhibits the highest efficiency with the values of Voc, Jsc, FF and η are 0.69 V, 8.60 mA cm-2, 67.93% and 4.06%, respectively.

An optical model is proposed in the white LED using phosphor and LED chip. In this paper a new model that describes the absorption rate and quantum efficiency with increasing the mixing ratio of phosphor in silicone, and the allotment of the phosphor absorption optical power in the several phosphor mixing in the silicone. Single phosphor in silicone from the optical measurement data before and after molding, the solution to get the blue optical power and the phosphor emission optical power is proposed. By these solution the absorption rate and the quantum efficiency was obtained. The model with single phosphor mixing in the silicone the validity was confirmed.

In this Paper, we have developed1 a low temperature process to make two type of Paste by using TIO2 nanoprticles(P25). The interconnections between substrate and TiO2 films or link between particles of free-binder Paste (FP1, FPZ, FP3) is very poor. Therefore, the Titanium(IV) isopropoxide was added to the TP paste to improve the interconnection. Electron transport time (Tt) and recombination time (Tr) are analyzed by IMPS (intensity-modulated photocurrent spectroscopy) and INIVS (Intensity-modulated photovltage spectroscopy). In the results, Tt of TP paste based DSSCs (about 4.3×10-3) is faster than other samples. Tt is Ionger from 2.7×10-2 s of FP2 to 3.0×10-2 s of TP. A solar conversion efficiency (DSSCs) of TP 15 3.54% for an incident solar energy of 100 mw cm-2(meanwhile, 2. 70% for DSSCs With FP2). The c아1versioIl efficiency is increased by 1.3 times.

DSSCs electrical characteristics and efficiency fabricated with different tape casting thickness Pt counter electrodes and different thickness between TiO2 photo electrode and Pt counter electrode substrate were studied. 1 layer Pt counter electrode shows 3.979% efficiency. Efficiency increased as tape casting thickness decreased. The lowest open-circuit voltage was a 0.726 V and the highest short-circuit current was a 2.188mA on 1 layer Pt counter electrode. On the different thickness between two substrates, the lowest open-circuit voltage 0.712 V and the highest short-circuit current 2.787mA was measured at 60 ㎛ surlyn film thickness and it shows the highest value of 5.067% efficiency.