Multilayer ceramic batteries (MLCBs) have attracted increasing attention as compact all-solid-state energy-storage devices that can be manufactured using multilayer ceramic processing technologies. In this study, an MLCC-compatible fabrication process for oxide-based MLCBs was developed using Li₁₊ₓAlₓTi₂₋ₓ(PO₄)₃ (LATP) solid electrolytes, Li₃V₂(PO₄)₃ (LVP) cathodes, and Cu current collectors. Commercial LATP powders were evaluated in terms of particle-size distribution, phase purity, thermal stability, and ionic conductivity. The selected LATP powder was subsequently employed for tape-cast green-sheet fabrication, and the effects of polyvinyl butyral (PVB) binder content on slurry rheology and sheet microstructure were investigated. An optimized binder composition containing 11 wt% PVB (BM-2/BH-3 = 3:7) provided improved processability and microstructural uniformity. Drying conditions during sequential electrode printing were also optimized to suppress sheet warpage and improve multilayer registration. Thermogravimetric and differential thermal analyses (TG–DTA) were used to establish an optimized two-step debinding and co-firing process under a controlled reducing atmosphere. The resulting multilayer structures exhibited uniform densification without significant blistering, delamination, or interfacial defects. Charge–discharge measurements confirmed that electrochemical functionality was retained after the complete manufacturing process, yielding a discharge capacity of approximately 2.5–2.7 μAh.

In this study, we systematically investigated the effects of thermal atomic layer deposition (ALD) conditions on the electrical characteristics of conductive-filament-based volatile threshold switching memristors with a Pt/Al₂O₃/Ag structure. Although volatile threshold switching memristors have attracted significant attention for neuromorphic computing applications such as spiking neural networks, the impact of dielectric deposition conditions on their switching behavior remains relatively unexplored. The number of ALD cycles was varied from 40 to 200, and the deposition temperature was varied from 50 to 250°C to evaluate their effects on threshold voltage (V_th), off-state resistance (R_off), and device yield. Devices fabricated using 75–150 ALD cycles showed clear volatile threshold switching behavior with relatively high device yield, whereas excessively low or high cycle numbers resulted in short-type and open-type failures, respectively. In addition, V_th and R_off tended to increase at higher deposition temperatures, while the device yield significantly degraded above 150°C. These results indicate that the number of ALD cycles and the deposition temperature define a critical process window for achieving volatile threshold switching while suppressing both short-type and open-type failures. This study provides practical guidelines for optimizing dielectric ALD conditions in conductive-filament-based volatile threshold switching memristors for future neuromorphic hardware applications.

The phase transition of Li₃PO₄ solid electrolyte for secondary batteries in vacuum has been studied by using real-time synchrotron X-ray scattering. According to the vacuum heating results, the crystal β-Li₃PO₄ phase was stable only from room temperature to 400°C. The crystal γ-Li₃PO₄ phase appeared at 410°C and the crystal β-Li₃PO₄ phase completely disappeared at 430°C. The transition from the β-Li₃PO₄ to the γ-Li₃PO₄ phases occurred primarily at 410°C, which is 40°C lower than the transition temperature of 450°C in air. The decrease in the phase transition temperature in vacuum, compared to that in air, is attributed to a relatively high concentration of oxygen vacancies. As the isothermal annealing time at 390°C was increased to 8 hours, the β-Li₃PO₄ phase was completely transitioned into the γ-Li₃PO₄ phase. Our study revealed the detailed transition behavior from the β-Li₃PO₄ to the γ-Li₃PO₄ phases during real-time annealing in vacuum.

Lead-free (Bi_1/2Na_1/2)TiO₃ (BNT)-based incipient piezoelectrics are highly promising for high strain actuators, but the high electric fields (4 ~ 6 kV/mm) required for activation limit practical device integration. In the current literature, large strains are frequently attributed to local structural variations like microscopic core-shell architectures. This work systematically investigates an alternative pathway by introducing A-site Strontium (Sr) excess non-stoichiometry into 0.74(Bi_1/2Na_1/2)TiO₃‒0.26SrTiO₃ (BNST26) ceramics. Microstructural and X-ray diffraction analyses reveal highly dense, uniform matrices completely devoid of micro-scale core-shell boundaries or macroscopic symmetry distortions, revealing that Sr non-stoichiometry diverges from typical Bi-excess mechanisms. Interestingly, despite negligible variations in overall macro-scale strain behavior across the composition series, a peak normalized strain (S_max/E_max) of approximately 804 pm/V is achieved at a low driving field of 2 kV/mm for the 1 mol% Sr-excess specimen (x = 0.010). These results indicate that while Sr non-stoichiometry weakly influences nanoscale stability, it can be inferred that subtle modifications of local defect configurations optimize switching energy barriers, enabling high-strain, low-drive-field performance in lead-free relaxors.

Ocean waves are not only a sustainable renewable energy source but also provide valuable information for monitoring marine environments and natural hazards. In this study, we developed a CNT/SEBS-based self-powered marine monitoring sensor utilizing a mechano-electrochemical mechanism, enabling simultaneous ultralow-frequency wave sensing and electrical energy harvesting. The developed sensor generated an open-circuit voltage of up to 60 mV and a short-circuit current of 80 μA/cm² without an external power source by exploiting variations in electrical double-layer capacitance induced by changes in the electrode–electrolyte interface. The capacitance increased from 0.1 μF to 2.4 μF with increasing immersion area, demonstrating the effectiveness of the proposed sensing mechanism. Furthermore, the CNT/SEBS bilayer exhibited high electrical conductivity together with excellent stretchability and flexibility, maintaining stable electrical responses under repeated water-level fluctuations. The proposed mechano-electrochemical self-powered sensor provides a promising platform for next-generation autonomous marine monitoring systems and sustainable blue-energy harvesting technologies.

We have studied the thermal stability of NCM622 cathode material for Li-ion batteries using real-time synchrotron x-ray scattering below 600°C in both air and vacuum. The expansion of the mean particle size, which reached maximum values of 10.3 μm in air and 10.6 μm in vacuum at 200°C, was attributed to the dehydration of intergranular water within the NCM622 powders. Across all annealing temperatures, the amount of crystal NCM622 phase in air was consistently higher than that in vacuum. The crystal domain sizes in air showed less variation than that in vacuum during annealing from RT to 500°C. These indicate that the crystal NCM622 phase is more thermally stable during annealing in air than in vacuum. This stability is attributed to the presence of 21% oxygen in air, which is absent under vacuum conditions.

Dye-sensitized solar cells (DSSCs) suffer from efficiency limitations due to interfacial charge recombination at the TiO₂/dye/electrolyte interface. In this study, aminopropyltrimethoxysilane (APS) was introduced onto nanoporous TiO₂ photoelectrodes via a dip-coating process with controlled coating times to investigate the effect of silanization time on interfacial charge transport behavior. Unlike concentration-driven structural modification, this work focuses on the evolution of the APS-modified interface governed by reaction time. The DSSC with 30 min APS treatment exhibited the highest power conversion efficiency of 5.34%, representing a 19% enhancement compared to the untreated device (4.49%), mainly due to increased short-circuit current density and open-circuit voltage. However, prolonged coating times (2 h and 24 h) resulted in a significant decrease in photocurrent density, leading to reduced device performance despite partial improvement in recombination resistance. These results are attributed to the time-dependent evolution of the APS interfacial layer. At moderate coating time, APS provides effective surface functionalization, enhancing dye adsorption and suppressing interfacial recombination. In contrast, prolonged coating is expected to induce increased surface coverage and silane condensation, which can hinder electron injection and increase charge transport resistance. Therefore, the photovoltaic performance is governed by a trade-off between recombination suppression and charge injection efficiency, controlled by the silanization time. This study highlights the critical role of interfacial reaction kinetics in determining charge transport behavior and provides an effective strategy for optimizing DSSC performance through time-dependent interface engineering.

Citations

• Enhanced charge transport characteristics of hydrothermally grown rutile TiO2 nanorod arrays for dye-sensitized solar cells
  Kyu Seop Choi, Hyung Jin Kim, Byungyou Hong
  Surfaces and Interfaces.2026; 98: 110402.     CrossRef

This study proposes an optimization strategy for the over-current protection (OCP) parameters of a lithium iron phosphate (LiFePO₄, LFP) battery system used in electric golf carts operating under high motor-load conditions. Real-world hillclimbing tests were conducted under four clearly defined payload/passenger conditions to analyze the transient discharge-current pro-file, voltage sag, and cell-temperature response. The maximum discharge current reached -238.2 A under the 200 kg cargopayload and one-passenger condition, and the current interval exceeding 150 A lasted up to 27 s. The maximum instantaneous power was 11.05 kW. Thermal analysis showed that the cell-temperature rise was within 2°C and the maximum measured cell temperature was 22.3°C. Linear regression of voltage and current yielded R² = 0.9368 and dV/dI = 0.0126 Ω, which was used as the DC internalresistance estimate. Based on these quantitative results and the cell specification limit of 300 A continuous discharge, the OCP threshold was reviewed from 250 A to 280 A to improve driving continuity while remaining below the allowable continuous-discharge current. EIS-based SOH estimation and the AI-BMS variable protection logic are presented as an extension framework for reflecting temperature and aging effects in future OCP-setting decisions.

This paper reviews the energy yield enhancement characteristics of bifacial photovoltaic systems combined with solar tracking, focusing on their performance relative to conventional monofacial fixed-tilt configurations. The fundamental mechanisms of yield improvement are summarized, highlighting the largely additive contributions of solar tracking, which increases front-side irradiance, and bifacial modules, which utilize rear-side reflected and diffuse radiation. Reported results from previous studies indicate that bifacial systems with single-axis tracking typically achieve 25–35% higher annual energy yield compared with standard monofacial fixed-tilt systems, with variations depending on environmental and design conditions. Key design and environmental considerations influencing system performance are discussed to provide practical insights for the application of bifacial tracking systems in utilityscale photovoltaic installations.

Polymer nanocomposites incorporating inorganic nanofillers have emerged as highly promising electromagnetic interference (EMI) shielding materials, combining mechanical compliance with robust conductive percolation networks. Carbon nanotubes (CNTs) are particularly attractive as conductive fillers because their high aspect ratio facilitates percolation at low loadings. Also, CNTs offer superior mechanical durability under deformation compared to rigid, fracture-prone metal nanowires. For EMI shielding, high electrical conductivity is critical as it enhances both reflection and absorption through efficient charge dissipation and conduction losses. However, achieving highly aligned conductive pathways without degrading the intrinsic electrical properties of CNTs remains a significant challenge. Here, we demonstrate a non-destructive magnetic surface-functionalization and alignment strategy. Using a polydopamine (PDA)-mediated route, pristine multiwalled CNTs are uniformly decorated with Fe₃O₄ nanoparticles (FMWCNTs). This enables highly effective magnetic field-driven alignment at fields as low as 10 mT, promoting the strategic formation of percolation networks. By optimizing the Fe₃O₄/MWCNT ratio for high saturation magnetization and uniform coverage, the aligned FMWCNTs exhibit significant electrical anisotropy, delivering a 10.7-fold higher electrical conductivity in the parallel configuration compared to the vertical configuration. These findings present a scalable, room-temperature platform for engineering directionally enhanced conductivity in polymer nanocomposites, with broad applicability in advanced EMI shielding, flexible electronics, and advanced packaging technologies.

Citations

• Interfacial Engineering of Composite Piezoelectric Fibers Via an Anchor-Chain Architecture
  Jun Liu, Qiao Zhou, Pengcheng Zhang, Shuying Hu, Fang Zhou, Shuangshuang Ren, Ting Guo, Leiying Miao
  ACS Applied Engineering Materials.2026; 4(8): 4367.     CrossRef

GaN nanowire (NW)-based hybrid structures have attracted attention for optoelectronic applications due to their high surface area and efficient carrier transport. However, the optical transparency of GaN NWs is often limited by unintended residual species accumulated on the surface and in the inter-wire regions, as well as defect-related absorption, leading to reduced light transmission. In this work, we demonstrate that thermal annealing significantly improves the optical transparency of GaN NWs grown on indium tin oxide (ITO)/glass substrates. The transmittance increased from 47.9% to 78.5% at 550 nm after rapid thermal annealing at 800^oC for 3 min, while a comparable value (~75.5%) was achieved at 600^oC for 5 min. PbBr₃ was deposited onto the GaN NWs to form hybrid structures, and temperature-dependent photoluminescence (TDPL) measurements revealed enhanced emission stability with suppressed peak shift and reduced spectral broadening. Arrhenius analysis based on a two-channel model revealed that the activation energy of the dominant non-radiative recombination pathway increased from 62 meV in the as-grown sample to 85 meV after thermal annealing, while its relative contribution remained nearly unchanged. In contrast, the shallow trap-assisted pathway exhibited a similar activation energy of approximately 6 meV in both samples, but its contribution decreased from 0.35 to 0.17 after annealing. As a result, the internal quantum efficiency (IQE) improved from 75.9% to 87.4%. These results show that thermal annealing improves optical transparency by removing residuals and suppresses defect-related recombination, leading to enhanced carrier dynamics and improved optical performance of PbBr₃-based hybrid structures.

Metamaterials, as artificially engineered structures with unconventional mechanical and acoustic properties, have recently emerged as a transformative platform for enhancing the capabilities of triboelectric nanogenerator (TENG) systems. Since the invention of TENG devices, extensive efforts have been devoted to improving charge density, output stability, and overall performance. Conventional performance optimization strategies mainly rely on device-level improvements such as surface chemistry modification, microstructuring, and nanopatterning. However, limited emphasis has been given to system-level development of smart self-powered intelligent systems. The integration of metamaterials into TENG devices opens a new era by enabling frequency-selective localization, mechanical impedance matching, and controllable deformation pathways. These engineered mechanical structures not only improve energy harvesting efficiency but also introduce new functionalities into the system. This review systematically summarizes recent advances in metamaterial-integrated TENG systems across four major application domains: (i) energy harvesting, (ii) acoustic telecommunication and acoustic-to-electric conversion, (iii) self-powered sensing, and (iv) vibration suppression and monitoring. Overall, the integration of metamaterials into TENG systems will pave the way for next-generation sustainable, intelligent, self-powered devices with diverse functionalities.

Citations

• Fabrication and performance of integrated self-powered PAAM hydrogel flexible pressure sensors
  Huaikuan Zang, Chao Hu, Pan Niu, Yong Zhang
  Materials Science in Semiconductor Processing.2026; 214: 110899.     CrossRef
• Highly Stretchable Multiphase Composite Piezoelectret With Large Longitudinal and Transverse Piezoelectric Sensitivity for Self-Powered Electromechanical Sensors
  Yanfeng Lyu, Tiantian Gao, Jian Li, Zheng Hu, Xunlin Qiu, Yanxun Xiang, Fu-Zhen Xuan, Wee Chen Gan, Dietmar Auhl
  IEEE Sensors Journal.2026; 26(18): 27090.     CrossRef

Neuromorphic computing, which mimics the energy-efficient parallel processing capabilities of the human brain, has emerged as an alternative to traditional von Neumann architectures that struggle with high power consumption in the era of artificial intelligence (AI). Despite the potential of Si-based neuromorphic chips, they often face fundamental limitations in integration density and biological compatibility, necessitating the development of next-generation devices that can better emulate the ionic signaling of biological systems. This review provides a comprehensive analysis of the recent research trends in artificial synapses and neurons based on organic electrochemical transistors (OECTs), highlighting their unique ability to achieve high transconductance and mixed ionic-electronic conduction at ultra-low operating voltages. We discuss how OECTs successfully replicate diverse synaptic plasticities and complex neuronal spiking behaviors through advanced material engineering and structural optimizations such as vertical architectures. Furthermore, this review discusses the implementation of high-order neural functions, including associative learning and logic operations, which are facilitated by the inherent electrochemical dynamics of organic semiconductors. Finally, overcoming current challenges in reliability and scalability will establish OECTs as a pivotal platform for low-power neuromorphic hardware and bio-integrated electronics.

Citations

• Analysis of Yield and Electrical Characteristics of Ag Electrode-Based Volatile Threshold Switching Memristors with Al2O3 Dielectric Films Under Different ALD Process Conditions
  Wan-Sik Woo, Seung-Jin Lee, Moon-Seok Kim, Seung-Bae Jeon
  Journal of Electrical and Electronic Materials.2026; 39(5): 493.     CrossRef

Electrochemical water splitting has emerged as a pivotal technology for green hydrogen production, offering a viable pathway toward a sustainable energy future. Among various electrolysis systems, Anion exchange membrane water electrolysis is particularly noteworthy as a cost-effective solution capable of operating under the fluctuating power inputs typical of renewable energy sources. However, the overall efficiency of water splitting is fundamentally limited by the oxygen evolution reaction, which exhibits sluggish kinetics compared to the hydrogen evolution reaction. While IrO₂ and RuO₂ serve as current benchmarks, their scarcity and high cost necessitate the development of earth-abundant alternatives. This review provides a comprehensive overview of fundamental OER mechanisms including the adsorbate evolution mechanism, lattice oxygen mechanism, and oxide path mechanism while highlighting how new pathways can circumvent traditional scaling relations. We discuss recent advancements in transition metal-based electrocatalysts, encompassing oxides, hydroxides, chalcogenides, phosphides, nitrides, and carbides, with a focus on innovative design strategies such as defect engineering, heteroatom doping, and heterostructure construction. This paper concludes by addressing current challenges and offering perspectives on future directions for the development of highly efficient and economically viable oxygen evolution electrocatalysts for large-scale applications.

MoS₂ has attracted significant attention as a next-generation semiconductor material to overcome the physical scaling limits of silicon-based devices due to its atomic thinness and excellent electrical properties. However, high contact resistance and the formation of Schottky barriers resulting from interface defects during the metal deposition process remain major bottlenecks that degrade overall device performance and reliability. In this study, we fabricated MoS₂ FETs by employing Sb₂Te₃, van der Waals (vdW) contacts. Minimized interface inhomogeneity was achieved through a hemispherical stamp-based dry transfer of h-BN for device encapsulation. h-BN encapsulation decreased the hysteresis window in the ±25 V gate voltage range from 17 V to 11.5 V compared to un-capped devices, confirming that charge trapping phenomena induced by external environmental factors were suppressed. Consequently, the dry transfer technique of h-BN using a hemispherical stamp demonstrated in this study provides a potential solution for securing the long-term reliability of MoS₂ devices with vdW contact by minimizing interface contamination.

This review systematically examines the structural characteristics, compositional design strategies, and recent research trends of layered double hydroxides (LDHs), which are recognized as promising electrocatalyst materials in electrochemical nitrate-to-ammonia conversion. Despite the rapid growth in related research, achieving simultaneous high selectivity and efficiency remains a significant technical challenge due to the complex mechanisms of the nitrate reduction reaction (NitRR) and its inherent competition with the hydrogen evolution reaction (HER). In this study, we analyzed the structural contributions of LDH catalysts for maximizing nitrate reduction efficiency and systematically established key catalyst design indicators required to ensure optimal performance. Specifically, we provide a detailed investigation of the physicochemical mechanisms for enhancing NH₃ production by precisely regulating the adsorption energies of reaction intermediates and maximizing charge transfer efficiency through compositional control and defect engineering. Furthermore, we discuss advanced structural design strategies, such as core-shell tandem structures, MOF-derived architectures, and interlayer anion control, as effective methods for enhancing catalytic performance and optimizing mass transport processes. These insights offer a strategic roadmap for designing high-performance LDH catalysts and represent a critical step toward the practical implementation of sustainable green ammonia production systems, particularly for integration into high-efficiency membrane electrode assembly (MEA) technologies.

Breakdown strength is an essential parameter for evaluating the electrical performance and degradation behavior of cable insulation and IEC 60243 also emphasizes its importance for detecting changes in insulation characteristics due to aging. However, the current IEC standards are mainly limited to specifying electrode configurations and test voltage conditions for breakdown tests, while the influence of insulating oil, is not clearly addressed. In this study, the breakdown strength of a 66 kV wet-type submarine cable was experimentally evaluated using insulating oils with different kinematic viscosities of 10, 100, 500, and 1,000 cSt in order to achieve reliable and reproducible breakdown measurements. The experimental results show that the measured breakdown strength decreases by up to approximately 20% depending on the oil viscosity. This indicates that the viscosity of the insulating oil has a significant influence on the measured breakdown strength during breakdown test. Therefore, it is necessary to perform breakdown strength measurements under identical test conditions, including the physical properties of the insulating oil, to ensure reliable comparison and accurate assessment of insulation performance and degradation characteristics.

The increasing global demand for renewable energy has accelerated the deployment of offshore wind farms, thereby highlighting the need for advanced development and performance assessment techniques for dynamic submarine cables used in floating offshore wind systems. These cables are continuously subjected to combined thermal, electrical, and mechanical stresses, with mechanical loading playing a particularly dominant role. As a result, dynamic submarine cables exhibit degradation behaviors that differ significantly from those of conventional fixed submarine cables. This paper presents the design and implementation of a comprehensive evaluation system capable of applying combined thermal, electrical, and mechanical stresses to dynamic submarine cables. The system was validated using a 66 kV wet type submarine cable through commissioning tests and insulation performance measurements. Electrical stress of 72 kV, thermal stress exceeding 95°C, and mechanical stress corresponding to a bending radius of 20 times the cable diameter over 20 cycles were applied to verify system reliability. The subsequent insulation assessments quantitatively confirmed performance variations induced by the combined stresses. The results demonstrate that the proposed platform is the first system capable of simultaneously applying thermal, electrical, and mechanical stresses to dynamic submarine cables, and its operational performance has been successfully validated. This platform enables realistic reliability evaluation of dynamic cables used in floating offshore wind farms and is expected to improve the overall operational reliability of offshore wind power systems.

The rapid proliferation of artificial intelligence (AI) servers and high-performance computing systems has significantly elevated the technical and reliability requirements for multilayer ceramic capacitors (MLCCs). In such systems, MLCCs are critical passive components that must deliver high capacitance, fast transient response, and robust insulation performance under high temperature, voltage, and current density. This review examines the material, structural, and process innovations that underpin MLCC performance in AI applications. Key topics include the development of ultrathin dielectric layers (<0.5 μm), rare-earth doped BaTiO₃-based dielectrics with enhanced DC bias stability, and core-shell microstructures designed for temperature and field resilience. The paper also explores insulation degradation mechanisms―such as vacancydriven conduction and demixing―and advanced reliability assessment methodologies, including HALT, TSDC, and the tipping point framework. Comparisons with automotive-grade MLCCs highlight the unique requirements of AI systems, such as ultraminiaturization, high volumetric efficiency, and ppm-level field failure rates. Finally, the review discusses emerging trends in MLCC technology, including particle engineering, interface stabilization, and advanced lamination techniques, and provides insight into the future direction of capacitor development tailored to AI data center environments.

Citations

• Reliability enhancement in Dy-doped BaTiO3 nanoceramics: from core–shell structure to phase-field modeling
  Shuyan Huang, Xinjie Wang, Mengjian Xiao, Xu Cheng, Xiaohui Wang
  Journal of Materials Science.2026; 61(37): 27665.     CrossRef
• Key factors determining high-temperature operating lifetime of multilayer ceramic capacitors (MLCCs)
  Yuto Tomura, Tzu-han Weng, Yusuke Oba, Tomohiro Kajita, Daiki Ishii
  Japanese Journal of Applied Physics.2026; 65(16): 16SP05.     CrossRef
• Effect of BaZrO3 Addition on the Frequency and Temperature Dependent Dielectric Properties of BaTiO3-Based Ceramics
  Won-Su Lee, Jong Kyu Lee, Moon-Taek Cho, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 478.     CrossRef
• Manufacturing Process Optimization of Oxide-Based Multilayer Ceramic Batteries Using Multilayer Ceramic Processing Technologies
  Won-Su Lee, Jong Kyu Lee, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 519.     CrossRef

The quench behavior of wires for superconducting fault current limiters at DC faults was simulated, with a focus on the effect of capacitor discharge on the quench. The behavior was also expressed in mathematical forms to facilitate a better understanding of the simulation results and for rough analytical estimations of the wire length suitable for the circuit voltage and capacitance. The quench resistance development behavior for various wire lengths and circuit capacitances was simulated using the model developed in the previous work. The quench behavior was expressed in mathematical forms, reflecting the concept of heat balance. During the quench, the wire temperature increased more slowly for longer wires, but was found to increase in a similar pattern. The wire length estimated by the mathematical formula was close to the one obtained by the simulation, with an error range of a few %. The calculations will be used to estimate effectively the length of wires needed to build superconducting fault current limiters for applications in DC power systems.

Cellulose nanofiber (CNF) has attracted significant attention as a next-generation insulating material due to its ecofriendly nature and outstanding functionalities. However, conventional kraft insulation paper suffers from limited dielectric breakdown strength and long-term reliability under high-voltage conditions, highlighting the need for alternative materials. In this study, kraft pulp was combined with five types of CNFs (A, B, C: wood-based / D, E: non-wood-based) to fabricate composite insulation papers, and their electrical and mechanical properties were systematically evaluated. The results showed that CNF incorporation generally enhanced density and tensile strength, while certain types contributed to lowering dielectric constant and improving breakdown strength. Among the wood-based CNFs, type C exhibited the most balanced performance in terms of dielectric stability and mechanical reinforcement. Among the non-wood-based CNFs, type E demonstrated notable improvements in structural compactness and tensile strength, suggesting favorable reliability. Therefore, this study identifies CNF C among wood-based types and CNF E among non-wood-based types as the most promising candidates for insulation performance enhancement, suggesting their applicability as next-generation insulating materials for power equipment and ecofriendly electronic devices.

Organic photovoltaics (OPVs) are attractive candidates for sustainable energy conversion due to their flexibility, lowcost processing, and compatibility with large-area fabrication. However, their efficiency is hindered by interfacial defects and vertical phase separation in the active layer, which induce charge imbalance and recombination losses. This work presents an interfacial engineering approach to overcome these limitations in P3HT:PC₇₀BM-based OPVs. Two key strategies were employed: (i) reducing the post-deposition annealing time of the active layer to suppress PC₇₀BM accumulation at the bottom electrode, and (ii) using a DCB:DCM mixed solvent system to regulate solvent evaporation, thereby promoting uniform film formation during PC₇₀BM overlay deposition. Devices fabricated with these optimizations exhibited notable enhancements, achieving short-circuit current density up to 15.83 mA/cm² and a 58.1% increase in power conversion efficiency compared to control devices. X-ray photoelectron spectroscopy confirmed reduced surface aggregation of PC₇₀BM, while X-ray diffraction indicated improved P3HT crystallinity and molecular ordering. These results highlight the critical role of interfacial and morphological control in enhancing charge separation and transport, offering a practical route toward efficient, reproducible, and stable OPVs.

The continuous rise of atmospheric carbon dioxide (CO₂) emissions highlights the urgent need for sustainable air purification technologies. Current Direct Air Capture (DAC) filters often rely on toxic amines, which limit long-term stability and safe application. Here, we report a non-toxic PAN-based nanofiber air filter fabricated by electrospinning and urea-assisted carbonization. Structural analyses confirmed the introduction of nitrogen functionalities that enhanced CO₂ affinity, while SEM and FT-IR revealed graphitic carbon formation. In air-chamber tests, the optimized carbonized nanofiber reduced CO₂ concentration from 25,000 ppm to 2,000 ppm, a level generally regarded as acceptable for indoor environments, while simultaneously removing over 95% of PM₁₀, PM_2.5, and PM_0.1 particulates. This dual functionality, combined with facile fabrication and material safety, demonstrates strong potential for PAN-derived carbon nanofiber membranes in DAC systems and eco-friendly air purification devices. These findings suggest a viable pathway toward scalable, sustainable air-filter technologies for carbon-neutral applications.

Humidity monitoring of exhaled breath has emerged as a vital approach for noninvasive respiratory health assessment, underscoring the need for sensitive and reliable humidity sensors. Despite its high conductivity and hydrophilic functional groups, reduced graphene oxide (rGO) often undergoes irreversible moisture adsorption and gradual oxidation by residual water, resulting in sensitivity degradation and long-term instability during cycling. In this study, a montmorillonite/reduced graphene oxide (MMT/rGO) composite is developed as a room-temperature humidity-sensing material, exhibiting an optimized response of 115%, more than 14 times higher than that of pristine rGO. This superior performance originates from the synergistic interaction between the reversible MMT swelling and the conductive rGO network near the electrical percolation transition, which ensures excellent stability and repeatability under repeated humidity cycles. These findings suggest that the MMT/rGO composite provides a cost-effective and biocompatible platform for next-generation wearable humidity sensors capable of continuous respiratory monitoring.

Silicon carbide (SiC), with its wide bandgap and strong resistance to radiation and thermal conditions, is a promising material for ultraviolet (UV) photodetector applications under harsh environments. In this study, porous SiC thin films with thicknesses of 20, 50, and 80 nm were fabricated on 4H-SiC substrates using aerosol deposition (AD), which enables roomtemperature film formation. The device with a 50 nm-thick film exhibited the highest photoresponse under UV-C illumination (260 nm), achieving a maximum photo-to-dark current ratio (PDCR) of 205.2, a responsivity of 0.058 A/W, an external quantum efficiency (EQE) of 27.71%, and a specific detectivity (D*) of 7.9×10¹¹ Jones. These results are attributed to an optimized balance between photon absorption and carrier transport in the porous structure. The findings confirm the potential of ADfabricated porous SiC films for highly sensitive and scalable UV photodetector applications.

Silicon carbide (SiC) power devices are attracting increasing attention for high-voltage and high-efficiency applications due to their superior material properties. However, achieving an optimal trade-off between specific on-resistance (Ron,sp) and breakdown voltage (BV) remains a key design challenge in planar MOSFET structures. In this study, twodimensional TCAD simulations were conducted to investigate the impact of varying the doping concentrations of the P-well (from 3 × 10¹⁷ to 6 × 10¹⁷ cm^-3) and JFET regions (from 1 × 10¹⁶ to 7 × 1016 cm^-3) on the electrical characteristics of 2.4 kVclass planar SiC MOSFETs. To maintain comparable BV conditions for 2.4 kV operation, two groups with P-well doping concentrations of 4.5 × 10¹⁷ cm^-3 and 5.3 × 1017 cm^-3 were analyzed and compared. When the P-well and JFET doping concentrations were 4.5 × 10¹⁷ cm^-3 and 1.5 × 10¹⁶ cm^-3, respectively, the simulated Ron,sp and BV were 1.41 mΩ·cm² and 3,150 V. In contrast, with P-well and JFET doping concentrations of 5.3 × 10¹⁷ cm^-3 and 5.0 × 10¹⁶ cm^-3, the Ron,sp was reduced to 1.31 mΩ·cm² while the BV slightly increased to 3,200 V. Based on these results, an optimized device structure was proposed, demonstrating its potential for integration into high-voltage SiC-based power systems. This study provides practical design insights and is expected to contribute to the advancement of wide bandgap semiconductor technologies for next-generation power electronics.

With the advancement of the information society, the demand for highly integrated and multi-functional electronic devices is rapidly increasing. To meet these demands, high-performance transistors with low power consumption, high-speed operating, and mechanical flexibility are essential. Among various candidates, semiconducting single-walled carbon nanotubes (s-SWCNT)-based transistors, which exhibit intrinsically ambipolar characteristics, have emerged as promising components for CMOS-like circuits. In this study, s-SWCNT were selectively dispersed using rr-P3DDT, a thiophene-based conjugated polymer, and filed-effect transistors (FETs) were fabricated by inducting directional alignment for enhanced charge transport through an off-centered spin-coating process. The electrical characteristics of the fabricated s-SWCNT FETs were evaluated under various thermal annealing conditions (100℃, 150℃, 200℃, and 250℃). Off-centered spin-coated and high temperature annealed s- SWCNT FETs exhibited high field-effect mobilities over 5 cm²/Vs in both p-type and n-type operation, along with ideal Vshaped ambipolar transfer curves. These results indicate a significant enhancement in ambipolar performance due to efficient desorption of residual oxygen and water molecules in active channel via high temperature annealing. Furthermore, CMOS-like inverter circuits demonstrated an ideal inversion voltage (VIN = V_DD/2) and a high voltage gain of approximately 9.5. These findings highlight the potential of SWCNT-based materials for realizing next-generation flexible electronic circuits that combine high-performance, energy efficiency, and simplified solution-processing.

Thermal batteries are designed to activate at high temperatures (~500℃), therefore, the electrodes used in these systems are typically made into pellet form using compression molding techniques that do not involve polymer binders. However, the compression molding technique poses limitations in scaling up the electrode area without increasing thickness for high-power properties. Additionally, the tape casting method has been studied as a way to solve with, but too low a loading level is still an obstacle to practical use. This study fabricated a film cathode of high loading level (35.79 mAh·cm^-2) using the tape casting method for these problem. As utilized fabricated cathode, it investigated the influence of electrode thickness and density on electrochemical performance. Furthermore, a film cathode with a larger area but the same amount of active material as the pellet was fabricated, enabling the design of high-power cells with the same energy density. We expect that the fabricated film cathode with a high loading level and scalable area will enable the development of various thermal battery designs.

Citations

• Manufacturing Process Optimization of Oxide-Based Multilayer Ceramic Batteries Using Multilayer Ceramic Processing Technologies
  Won-Su Lee, Jong Kyu Lee, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 519.     CrossRef

Multilayer ceramic capacitors (MLCCs) are essential for high-capacitance, miniaturized, and reliable electronic applications. This study examines the impact of layer stacking on the dielectric and electrical properties of MLCCs using a BaTiO₃-based dielectric with MgO, Mn₃O₄, Yb₂O₃, V₂O₅, and (BaCa)SiO₃ glass additives. MLCCs with 10 um-thick dielectric layers and varying Ni electrode layers (10, 30, 50, and 100 layers) were fabricated. The dielectric constant increases significantly up to 30 layers due to compressive stress and sintering densification but it becomes linear beyond 30 layers. Dissipation factor and ESR decrease with higher stacking due to improved sinterability, while breakdown voltage declines exponentially from defect accumulation and thermal stress. Insulation resistance decreases but stabilizes relative to capacitance. C-V results show stress-induced polarization suppression, which reduces the dielectric constant under high voltage. Optimized stacking and sintering conditions are crucial for MIL-PRF-32535 compliant MLCC designs.

Citations

• [100]-Oriented BaTiO₃ via reaction-mediated texturing with SrTiO₃ templates
  Nu-Ri Ko, Jinsung Chun, Kutak Lee, Chang Kyu Jeong, Wook Jo
  Journal of the Korean Ceramic Society.2026; 63(4): 574.     CrossRef
• Effect of BaZrO3 Addition on the Frequency and Temperature Dependent Dielectric Properties of BaTiO3-Based Ceramics
  Won-Su Lee, Jong Kyu Lee, Moon-Taek Cho, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 478.     CrossRef

Abstract In this study, to develop composition ceramics for energy harvesting devices, Pb(Ni_1/3Nb_2/3)O₃-Pb(Zr Ti)O₃ system ceramics substituted with Pb(Mg_1/2W_1/2)O₃ were manufactured by conventional mixed oxide method using Li₂CO₃ and Na₂CO₃ (LNCO) as sintering aids. Their microstructure and piezoelectric properties were also investigated. At the specimen sintered at 930℃, high values of piezoelectric properties appeared: the dielectric constant (εr) of 2,522 planar electromechanical coupling factor kp of 0.602, and k₃₁ of 0.385, d31 = 229 [pC/N], g₃₁ = 10.13 [mV.m/N], Qm of 70, respectively. These values were suitable for the application of devices such as energy harvesting devices and ultrasonic devices.

Citations

• Optimization of the annealing process significantly enhances the breakdown field strength and energy storage performance of Pb0.92La0.08(Zr0.52Ti0.48)O3 thin films
  Dongchun Qiu, Jianing Zhu, Piyu Gong, Shibing Xiao, Huiting Sui, Huajun Sun
  Journal of Alloys and Compounds.2026; 1080: 190542.     CrossRef
• Low-Temperature Sintering and Piezoelectric Properties of the PZN-PZT Ceramics with LiBiO2
  Nayoon Kwon, Yong Geun Choi, Young Jin Lee, Dong Hun Yeo, Hyo Soon Shin, Joon-Hyung Lee
  Journal of Electrical and Electronic Materials.2026; 39(5): 501.     CrossRef