We have studied the thermal stability of NCM622 cathode material for Li-ion batteries using real-time synchrotron x-ray scattering below 600°C in both air and vacuum. The expansion of the mean particle size, which reached maximum values of 10.3 μm in air and 10.6 μm in vacuum at 200°C, was attributed to the dehydration of intergranular water within the NCM622 powders. Across all annealing temperatures, the amount of crystal NCM622 phase in air was consistently higher than that in vacuum. The crystal domain sizes in air showed less variation than that in vacuum during annealing from RT to 500°C. These indicate that the crystal NCM622 phase is more thermally stable during annealing in air than in vacuum. This stability is attributed to the presence of 21% oxygen in air, which is absent under vacuum conditions.
Renewable energy harvesting technologies, which convert ambient resources such as wind into electrical energy, have attracted significant attention as sustainable power sources for self-powered systems. However, the long-term applicability of wind energy harvesters in remote or extreme environments has not yet been fully discussed, particularly in terms of structural robustness and environmental adaptability. In this study, we designed a double-clamped flutter-type triboelectric generator (DFTEG) for efficient wind energy harvesting and evaluated its output performance under various simulated outdoor conditions. The DFTEG features a modular acrylic frame with a magnet-based assembly for easy maintenance and film replacement, utilizing PTFE films and aluminum electrodes to maximize the charge density difference according to the triboelectric series. Structural optimization revealed that a single-film configuration with a length of 110 mm produced the most stable flutter vibration and a large effective contact area, achieving a maximum open-circuit voltage of 42.28 V and a short-circuit current of 2.89 μA. Furthermore, performance evaluations under various environmental variables, including relative humidity, temperature, and sand particles interference, confirmed consistent electrical output across diverse environmental conditions. These results demonstrate the potential of the proposed DFTEG as an environmentadaptive independent power source capable of stable operation under complex environmental factors.
The rapid proliferation of artificial intelligence (AI) servers and high-performance computing systems has significantly elevated the technical and reliability requirements for multilayer ceramic capacitors (MLCCs). In such systems, MLCCs are critical passive components that must deliver high capacitance, fast transient response, and robust insulation performance under high temperature, voltage, and current density. This review examines the material, structural, and process innovations that underpin MLCC performance in AI applications. Key topics include the development of ultrathin dielectric layers (<0.5 μm), rare-earth doped BaTiO₃-based dielectrics with enhanced DC bias stability, and core-shell microstructures designed for temperature and field resilience. The paper also explores insulation degradation mechanisms―such as vacancydriven conduction and demixing―and advanced reliability assessment methodologies, including HALT, TSDC, and the tipping point framework. Comparisons with automotive-grade MLCCs highlight the unique requirements of AI systems, such as ultraminiaturization, high volumetric efficiency, and ppm-level field failure rates. Finally, the review discusses emerging trends in MLCC technology, including particle engineering, interface stabilization, and advanced lamination techniques, and provides insight into the future direction of capacitor development tailored to AI data center environments.
Metal halide perovskite materials have emerged as promising candidates for next-generation optoelectronic applications owing to their outstanding optical properties and tunable emission characteristics. However, their practical application is hindered by poor environmental stability, especially under conditions of heat, moisture, and UV exposure, necessitating effective encapsulation strategies. This review summarizes recent progress in enhancing the environmental stability of perovskite nanocrystals through polymer matrix embedding, inorganic oxide encapsulation, and compositionally matched core-shell structures using homogenous perovskite derivatives. We discuss how polymers enhance the environmental and moisture stability of perovskite nanocrystals, how oxide-based shells (e.g., SiO₂, TiO₂) contribute to thermal robustness and barrier protection, and how homostructural core-shells provide lattice-matched defect passivation with improved long-term durability. A comprehensive understanding of the advantages and limitations of each encapsulation strategy, along with their rational integration, can accelerate the commercialization of perovskite-based technologies in various applications such as highcolor- purity displays, color conversion filters, and flexible optoelectronic devices.
With the recent active development of laser-based weapons/monitoring/communication systems, there is a significant increase in the demand for improved performance of piezoelectric actuators, a key component of both deformable mirror (DM) and fast steering mirror (FSM) in the systems. The conventional polycrystalline piezoelectric ceramic actuators have limitations in improving their characteristics, so the ultrahigh strain PMN-PZT piezoelectric single crystal multilayer actuators have been developed. In this study, the basic experimental methods were developed to evaluate their stability as well as reliability. The limitations of deformation and applied voltage were confirmed through the breakdown voltage test, and the degree of stability was confirmed through the hammering test. In this study, the breakdown voltage test and the hammering test were confirmed to be effective methods to evaluate their stability as well as reliability. Through these studies, the next-generation PMN-PZT piezoelectric single-crystal multilayer actuator is expected to be applied to various piezoelectric application fields by securing reliability as well as excellent piezoelectric properties.
Next-generation wide-bandgap semiconductors such as SiC, GaN, and Ga2O3 are being considered as potential replacements for current silicon-based power devices due to their high mobility, larger size, and production of high-quality wafers at a moderate cost. In this study, we investigate the gradual modulation of chemical composition in multi-stacked metal oxide semiconductor thin films to enhance the performance and bias stability of thin-film transistors (TFTs). It demonstrates that adjusting the Ga ratio in the indium gallium oxide (IGO) semiconductor allows for precise control over the threshold voltage and enhances device stability. Moreover, employing multiple deposition techniques addresses the inherent limitations of solution-processed amorphous oxide semiconductor TFTs by mitigating porosity induced by solvent evaporation. It is anticipated that solution-processed indium gallium oxide (IGO) semiconductors, with a Ga ratio exceeding 50%, can be utilized in the production of oxide semiconductors with wide band gaps. These materials hold promise for power electronic applications necessitating high voltage and current capabilities.
This research explores the development of [100]-textured barium titanate (BaTiO3, BT) ceramics using sodium bismuth titanate (Na0.5Bi4.5Ti4O15, NBiT) templates, aimed at leveraging the inherent high dielectric property of BT. However, the attempted texturing was unsuccessful, primarily due to bismuth diffusion from the NBiT templates into the BT matrix below the sintering temperature, at 1,000℃. Systematical exploration about the cause of the failure is involved and alternative approaches are proposed in detail to overcome the challenge. These findings contribute to the understanding of techniques and conditions for textured ceramic fabrication and highlight the need for further research in this area.
Piezoelectric actuators, which utilize piezoelectric crystals or ceramics, are commonly used in precision positioning applications, offering high-speed response and precise control. However, the use of low-performance ceramics and expensive single crystals is limiting their versatile use in the actuator market, necessitating the development of both high-performance and cost-effective piezoelectric materials capable of delivering higher forces and displacements. The use of textured Pb (lead)-based piezoelectric ceramics formed by so-called templated grain growth method has been identified as a promising strategy to address the performance and cost issue. This review article provides insights into recent advances in texturing Pb-based piezoelectric ceramics for improved performance in actuation applications. We discussed the relevant issues in detail focusing on current challenges and emerging trends in the textured piezoelectric ceramics for their reliability and performance in actuator applications. We discussed in detail focusing on current challenges and emerging trends of textured piezoelectric ceramics for their reliability and performance in actuator applications. In conclusion, the article provides an outlook on the future direction of textured piezoelectric ceramics in actuator applications, highlighting the potential for further success in this field.
According to the recent global warming, it is necessary to use energy efficiently together with eco-friendly energy. The development of alternative technologies is requisite for managing the current energy and climate crises. In this regard, “smart windows,” which can control solar radiation, can be used to mitigate energy demands. Electrochromic devices (ECDs) effectively control the amount of solar energy reaching commercial and other living areas and maintain climate conditions via color modulation in response to small external stimuli, such as temperature and light irradiation. However, the performance and the stability of ECDs depend on the state of the electrolyte and sealing of the device. To resolve the aforementioned issues, an ECD was manufactured by using a poly (methyl methacrylate) (PMMA)-based gel polymer electrolyte (GPE), and a laminating method was used to adequately seal the ECD. The concentrations of PMMA, acetonitrile (ACN), and ferrocene (Fc) were controlled to optimize the composition of the GPE to achieve an enhanced electrochromic performance. The fabricated GPE-based ECD afforded high optical contrast (~81.92%), with high electrochromic stability up to 10,000 cycles. Moreover, the lamination method employing the GPE could be used to fabricate large-area ECDs.
With the recent increase in demand for electronic devices, multi-layer ceramic capacitors (MLCCs) have become the most important core component. In particular, the next-generation MLCC with extremely high reliability is required for the 4th industrial revolution and electric vehicle applications. Therefore, it is necessary to develop dielectric ceramic materials with high dielectric properties and reliability. During the decades, electrical properties of BaTiO3 based dielectric ceramics, which have been widely used in MLCC industrial field, have been improved by microstructure and defect chemistry control. However, electrical properties of BaTiO3 have reached their limits, and new types of dielectric materials have been widely studied. Based on these backgrounds, this report presents the recent development trends of BaTiO3-based dielectric materials for the nextgeneration MLCCs, and suggests promising candidates to replace BaTiO3 ceramics.
In recent years, the challenge of higher energy efficiency has emerged as urban buildings have become taller, and the area of window glasses has increased. To address the problem of energy efficiency in buildings, research on smart windows is being actively conducted. In this study, an accelerated experiment for thermal stability was conducted to fabricate a liquid crystal cell applicable to external windows. It was confirmed from the study that the function is maintained even in a high-temperature external environment through the change in transmittance by voltage. Compared with the initial transmittance, after the passage of time, the smart window cell to which the sealant was applied showed a small change in transmittance of 1~2%. This result confirmed the thermal stability of the liquid crystal-based smart window.
Smart windows are used as windows and doors to determine the cooling and heating efficiency of a building. They have characteristics that can increase the energy efficiency of a building, which leads to energy savings. In addition, smart windows can control the amount of light transmitted from the external environment of a building to the interior of a building according to the needs of the user. In this study, a 297×210 mm2 liquid crystal cell capable of controlling light transmittance was fabricated using a liquid crystal device as an optical shutter. The effect of driving voltage on the transmittance and the effect of the thermal environment on the driving stability were analyzed. We confirmed the applicability of using smart windows as exterior building materials.
Thin film transistors (TFTs) with large-area, high mobility, and high reliability are important factors for next-generation displays. In particular, thin transistors based on IGZO oxide semiconductors are being actively researched for this application. In this study, several methods for improving the reliability of a-IGZO TFTs by applying various materials on a passivation layer are investigated. In the literature, inorganic SiO2, TiO2, Al2O3, ZTSO, and organic CYTOP have been used for passivation. In the case of Al2O3, excellent stability is exhibited compared to the non-passivation TFT under the conditions of negative bias illumination stress (NBIS) for 3 wavelengths (R, G, B). When CYTOP passivation, SiO2 passivation, and non-passivation devices were compared under the same positive bias temperature stress (PBTS), the Vth shifts were 2.8 V, 3.3 V, and 4.5 V, respectively. The Vth shifts of TiO2 passivation and non-passivation devices under the same NBTS were -2.2 V and -3.8 V, respectively. It is expected that the presented results will form the basis for further research to improve the reliability of a-IGZO TFT.
In this work, we evaluated the structural, electrical and optical properties of Ge8Sb2Te11 and Cu-doped Ge8Sb2Te11 thin films prepared by rf-magnetron reactive sputtering. The 200-nm-thick deposited films were annealed in a range of 100~400℃ using a furnace in an N2 atmosphere. The amorphous-to-crystalline phase changes of the thin films were investigated by X-ray diffraction (XRD), UV-Vis-IR spectrophotometry, a 4-point probe, and a source meter. A one-step phase transformation from amorphous to face-centered-cubic (fcc) and an increase of the crystallization temperature (Tc) was observed in the Cu-doped film, which indicates an enhanced thermal stability in the amorphous state. The difference in the optical energy band gap (Eop) between the amorphous and crystalline phases was relatively large, approximately 0.38~0.41 eV, which is beneficial for reducing the noise in the memory devices. The sheet resistance(Rs) of the amorphous phase in the Cu-doped film was about 1.5 orders larger than that in undoped film. A large Rs in the amorphous phase will reduce the programming current in the memory device. An increase of threshold voltage (Vth) was seen in the Cu-doped film, which implied a high thermal efficiency. This suggests that the Cu-doped Ge8Sb2Te11 thin film is a good candidate for PRAM.
In this study, we fabricated plate-type shunt resistors with thermal stability by parallelly connecting metal alloy plates with positive temperature coefficient of resistance (TCR) and carbon nanotube (CNT) plates with negative TCR. The metal alloy plates, which were prepared by alloying Cu and Mn with a composition of 91 wt% of Cu and 9 wt% of Mn, showed around 800 ppm/℃ of TCR, and the CNT plates prepared from the CNT solution by using the vacuum filtration method showed around -800 ppm/℃ of TCR. The shunt resistor that was fabricated by stacking metal alloy plates and CNT plates in this work showed about 46.93 ppm/℃ of TCR. Therefore, we conclude that a shunt resistor with low TCR can be realized by simply adjusting the TCR of the metal alloy only, because the TCR of the CNT plate has an identical value.
Porcelain insulators have been used mainly for power line fixing and electrical insulation in transmission towers. Porcelain insulators have generally a 30 years desired life, but over 50% exceed their life expectancy. Since the damage to porcelain insulators is usually accompanied by enormous loss of human resource material, their efficient maintenance has emerged as an important issue. In this regard, this study applied a frequency response function (FRF) for integrity assessment of the insulator. The characteristics of the FRF according to damage types were identified and analyzed by the change in natural frequencies, curve shape, attenuation, and Nyquist diagram stability. The results showed significant differences in the FRF according to damage types, which can be used as basic data for the effective integrity assessment of porcelain insulators.
This study discusses and demonstrates the structural stability of highly ordered Pt patterns formed on a transparent and flexible substrate through the process of nanotransfer printing (nTP). Bending tests comprising approximately 1,000 cycles were conducted for observing Pt line patterns with a width of 1 μm formed along the direction of the horizontal (x-axis) and vertical (y-axis) axes (15 mm × 15 mm); and adhesion tests were performed with an ultrasonicator for a period greater than ten minutes, to analyze the Pt crossbar patterns. The durability of both types of patterns was systematically analyzed by employing various microscopes. The results show that the Pt line and Pt crossbar patterns obtained through nTP are structurally stable and do not exhibit any cracks, breaks, or damages. These results corroborate that nTP is a promising nanotechnology that can be applied to flexible electronic devices. Furthermore, the multiple patterns obtained through nTP can improve the working performance of flexible devices by providing excellent structural stability.
Ni-InGaAs shows promise as a self-aligned S/D (source/drain) alloy for n-InGaAs MOSFETs (metal-oxide-semiconductor field-effect transistors). However, limited thermal stability and instability of the microstructural morphology of Ni-InGaAs could limit the device performance. The in situ deposition of a Pd interlayer beneath the Ni layer was proposed as a strategy to improve the thermal stability of Ni-InGaAs. The Ni-InGaAs alloy layer prepared with the Pd interlayer showed better surface roughness and thermal stability after furnace annealing at 570℃ for 30 min, while the Ni-InGaAs without the Pd interlayer showed degradation above 500℃. The Pd/Ni/TiN structure offers a promising route to thermally immune Ni-InGaAs with applications in future n-InGaAs MOSFET technologies.
The white light of a hybrid LED is obtained by using red and green organic fluorescent layers made of polymethylmethacrylate (PMMA) films, which function as color down-conversion layers of blue light-emitting diodes. In this research, we studied the fluorescence properties of a red organic fluorophore, employing perylene bisimide derivatives applicable to hybrid LEDs. The solubility, thermal stability, and luminous efficiency are important characteristics of organic fluorophores for use in hybrid LEDs. The perylene fluorescent compounds (1A and 1B) were prepared by the reaction of 4-bromophenol and 4-iodophenol with N,N`-bis(4-bromo-2,6-diisopropylphenyl)-1, 6,7,12-tetrachloroperylene-3,4,9,10-tetracarboxyl diimide (1) in the presence of dimethyl formaldehyde (DMF) at 70℃. The synthesized derivatives were characterized by using 1H-NMR, FT-IR, UV/Vis absorption and PL spectra, and TGA analysis. Compounds 1A and 1B showed absorption and emission at 570 nm and 604 nm in the UV/Vis spectrum. We also documented favorable solubility and thermal stability characteristics of the perylene fluorophores in our work. Perylene fluorophore 1, with the 4-bromophenol substituent 1A, exhibited particularly good thermal stability and solubility in organic solvents.
Transparent film heaters employing silver nanowires (Ag NWs) have attracted increasing attention because of their widespread applications. However, the low thermal resistance of Ag NWs limits the maximum operating temperature of the Ag NW film heater. In this study, Ag NW film heaters with high mechanical and thermal stability were successfully developed. The thermal power-out characteristics of the Ag NW heaters were investigated as a function of the Ag NW density. The results revealed that the prepared flexible Ag NW heater possessed high thermal stability over 190℃ owing to ZnO encapsulation. This indicates that the Ag NW film with excellent thermal stability have remarkably high potential for use as electrodes in film heaters operating at high temperatures.
Thermal and structural stability in the glass transition region of chalcogenide glasses has been investigated in terms of thermodynamics for application to various optoelectronic devices. In this study, the compositions of GexSb20Se80-x (x = 10, 15, 20, 25, and 30) were selected to investigate the glass stability according to germanium ratios. The chalcogenide bulks were fabricated by using a traditional melt-quenching method. Thin films were deposited by a thermal evaporation system, maintaining the deposition ratio of 3~5 A in order to have uniformity. The thermal and structural properties were measured by a differential scanning calorimeter (DSC) and X-ray diffraction (XRD). The DSC analysis provided thermal parameters and theoretical glass region stabilities. The XRD analysis supported the theoretical stabilities because of where the crystallization peak data occurred.
This work reports the phase-change behavior and thermal stability of doped GeSbTe/GeSbTe bilayers. We prepared the bilayers using RF sputtering, and annealed them at annealing temperature ranging from 100℃ to 400℃. The sheet resistance of the bilayer decreased and saturated with increasing annealing temperature, and the saturated value was close to that of pure GeSbTe film. The surface of the bilayer roughened at 400℃, which corresponds to the surface roughening of doped GeSbTe film. Mixed phases of face-centered cubic and hexagonal close-packed crystalline structures were identified in the bilayers annealed at elevated temperature. These results indicate that the phase-change behavior of the bilayer depends on the concurrent phase-transitions of the two GeSbTe-based films. The dopants in the doped GeSbTe film were diffused out at annealing temperatures of 300℃ or higher, which implies that the thermal stability of the bilayer should be considered for its application in phase-change electronic devices.
We report the studies on the red organic phosphor by using perylene bisimide derivatives. Even though perylene bisimide derivatives have excellent thermal stability and luminous efficiency, they have low solubility in organic solvents. In this research, modified perylene bisimide derivative, N,N`-Bis(4-bromo-2, 6-diisopropylphenyl)- 1, 6, 7, 12-tetraphenoxyperylene-3, 4, 9, 10-tetracarboxyl bisimide (1C), has been prepared by the reaction of phenol with N,N`-Bis(4-bromo-2, 6-diisopropylphenyl)-1, 6, 7, 12-tetrachloroperylene-3, 4, 9, 10-tetracarboxyl bisimide (1B) in presence of DMF, at 70℃. The synthesized (1C) was characterized by using 1H-NMR, FT-IR, UV/V is spectroscopy, and TGA. The absorbtion and emission of (1C) was shown at 576 nm and 610 nm in UV/V is spectrum. In TGA thermogram, (1C) showed good thermal stability without significant weight loss to 220℃. And in the solubility analysis, (1C) with phenoxy group showed the good solubility in general organic solvents. The blended films of (1C) with PMMA (polymethyl methacrylate) at different weight % concentration such as 10, 5, 1 weight % have been prepared. The blended film was shown at 616 nm when monitored at 450 nm in PL emission spectra.
CNT (carbon nanotube) resistors with low resistance and negative TCR (temperature coefficient of resistance) were fabricated with yarned CNT (carbon nanotube) fibers. The CNT fibers were prepared by yarning CNTs grown on the silicone substrate by CVD (chemical vapor deposition) method. The CNT resistors were fabricated by winding CNT fibers on the surface of ceramic rod. Both metal terminals were connected with the CNT fiber wound on the ceramic rod. We measured electrical resistance and thermal stability with the number of CNT fibers wound. The CNT resistor system shows linearly decreased resistance with the number of CNTs wound on the ceramic rod and saturated at 20 strands. The CNT resistor system has negative TCR between -1,000 ~ -2,000 ppm/℃ and stable frequency properties under 100 kHz.
In this paper, we fabricated Cu/Mn alloy shunt resistor with low resistance and thermal stability for use of mobile electronic devices. We designed metal alloy composed of copper (Cu) and manganese (Mn) to embody in low resistance and low TCR which are conflict each other. Cu allows high electrical conductivity and Mn serves thermal stability in this Cu/Mn alloy system. We confirmed the elemental composition of the designed metal alloy system by using energy dispersive X-ray (EDX) analysis. We obtained low resistance below 10 mΩ and low temperature coefficient of resistance (TCR) below 100 ppm/℃ from the designed Cu/Mn alloy resistor. And in order to minimize resistance change caused by alternative frequency on circuit, shape design of the metal alloy wire is performed by rolling process. Finally, we conclude that design of the metal alloy system was successfully done by alloying Cu and 3 wt% of Mn, and the Cu/Mn alloy resistor has low resistance and thermal stability.
In this research, we focused on the improvement of cy3 dye’s characteristics for LCD color filter. Solubility and thermal stability are main characteristics of dyes for LCD color filter. We performed experiment to change counter cation of cy3 dyes with alkoxy substituent for these purposes. These cy3 dyes (1b∼5b) were prepared through the synthetic procedure of three steps. The synthesized new cy3 dyes were charaterized by using NMR, FT-IR, UV/Vis spectroscopy, and TGA. These cy3 dyes showed purple color and maximum absorption wavelength (λmax) in the range of 578∼590 nm in UV/Vis spectrum. We confirmed that solubility and thermal stability of cy3 dyes were dependent on the structure of counter cation. Cy3 dyes with alkoxy substituent have good solubility in organic solvents such as dichloromethane, methanol, and acetone. Especially, Cy3 dye with 4-nitrobenzyl counter cation (5b) gave excellent solubility characteristics.
Thermal batteries are heat-activated primary reserve power sources that use inorganic salt as electrolytes and specially designed to meet extremely long or environmentally severe storage requirements. They are primarily used to deliver high power for relatively short periods in such applications as fuzes, missiles, ordnance and other military applications. In this paper, we describe a general overview and research trends on electrode materials for thermal batteries.
We studied white organic light-emitting diodes using blue fluorescent and red phosphorescent materials.White single OLEDs were fabricated using SH-1 : BD-2 (3 vol.%) and CBP : Ir(mphmq)2(acac) (2 vol.%) as emitting layer (EML). The white single OLED using SH-1 : BD-2 (3 vol.% 8 nm) / CBP : Ir(mphmq)2(acac) (2vol.% 22 nm) as emitting layer showed maximum current efficiency of 8.8 cd/A, Commission Internationale del``Eclairage (CIE) coordinates of (0.403, 0.351) at 1,000 cd/㎡, and variation of CIE coordinates with (0.402 ±0.012, 0.35 ± 0.002) from 500 to 3,000 cd/㎡. The white tandem OLED using SH-1 : BD-2 (3 vol.% 12 nm) /CBP : Ir(mphmq)2(acac) (2 vol.% 18 nm) showed maximum efficiency of 19.6 cd/A, CIE coordinates of (0.354,0.365) at 1,000 cd/㎡, and variation of CIE coordinates with (0.356 ± 0.016, 0.364 ± 0.002) from 500 to 3,000 cd/㎡. Maximum current efficiency of the white tandem OLED was more twice as high as the single OLED. Our findings suggest that tandem OLED was possible to produce improved efficiency and excellent color stability.
Recently, ZnO based oxide TFTs used in the flexible and transparent display devices are widely studied. To apply to OLED display switching devices, electrical performance and stability are important issues. In this study, to improve these electrical properties, we fabricated TFTs having Al doped Zinc Oxide (AZO) layer inserted between the gate insulator and ZnO layer. The AZO and ZnO layers are deposited by Atomic layer deposition (ALD) method. I-V transfer characteristics and stability of the suggested devices are investigated under the positive gate bias condition while the channel defects are also analyzed by the photoluminescence spectrum. The TFTs with AZO layer show lower threshold voltage (Vth) and superior sub-threshold slop. In the case of Vth shift after positive gate bias stress, the stability is also better than that of ZnO channel TFTs. This improvement is thought to be caused by the reduced defect density in AZO/ZnO stack devices, which can be confirmed by the photoluminescence spectrum analysis results where the defect related deep level emission of AZO is lower than that of ZnO layer.
In this research, we focused on the development of cy3 dye with high thermal stability and good solubility for LCD color filter. Cy3 dyes were prepared through the synthetic procedure of two steps. The synthesized cy3 dyes were characterized by using NMR, FT-IR, UV/Vis spectroscopy, and TGA. These cy3 dyes showed maximum absorption wave length (λmax) in the range of 549∼555 nm in UV/Vis spectrum. And we confirmed that solubility characteristics and thermal stability of cy3 dyes were dependent on the structure of counter cation. Cy3 dyes with methyl counter cation and ethyl counter cation have good solubility in organic solvents such as chloroform, ethanol, and PGME. Moreover, Cy3 dye with ethyl counter cation gave excellent thermal stability in TGA thermograms. And Cy3 dye with ethyl counter cation showed good result in photoresist film test.
First
Prev
